您要查找的是不是:
- LANDING GEAR BYPASS VALVE CONTROL. 起落架旁通活門控制。
- Remove the body bolts from the valve body. 從閥體上拆卸閥體螺栓。
- Lift retainer and check assembly from valve body. 從閥體內取出護圈和止回閥總成。
- Screw the cover onto the valve body. 將閥蓋旋在閥體上。
- Turn handle to be perfectly perpendicular to valve body. 將手柄旋轉到與閥體完全垂直的位置。
- Remove the body bolts from valve body using Allen Key. 採用內六角扳手從閥體上拆卸閥體螺栓。
- Installation suggestion: valve body vertical and upward. 建議安裝方式,閥體垂直向上。
- Application of Combining Tech of Perforation With Passing Pressure by Bypass Valve and APR Test Tool. 旁通傳壓射孔與APR測試工具聯作技術的應用
- IMPORTANT! Flow must always be in direction of arrow on valve body. 重要提示!水流流向必須與閥體上的箭頭方向一致。
- Insert valve body through mounting hole and seat lugs. 將閥體插入安裝孔和密封連接盤。
- Prepare suitable connection for 1?」 threaded nipple provided in down stream of bypass valve for chemical feeding. 對在旁通閥下游裝設的1?」螺紋接套準備合適的連接,以供化學進料。
- Press stem/ball into valve body and remove from open end. 將閥桿/球體壓入閥體內,並且從開口端卸下來。
- The top of retainer must drop just below threads in the valve body. 護圈上方必須放置在閥門閥體螺紋以下。
- Turbine bypass hydraulic control system mainly consists of oil supply device, bypass valve hydraulic actuator, oil line and accessories. 汽輪機旁路液壓控制系統主要包括:供油裝置、旁路閥門液壓執行機構、油管路及附件。
- The Eaton superchargers also use a bypass valve that equalizes the pressure on both sides of the impellers when the engine is operating in vacuum. 伊芳頓增壓器也使用那使相等的閥門支路當發動機營運時,對葉輪的雙方的壓力在真空里。
- Slide one half of the splash guard into the groove on the relief valve body. 將防濺保護的一半滑動到安全閥閥體的溝槽上。
- The port labeled as Boost Port 2 is also a port that will provide access to boost pressure, but it is normally connected to the bypass valve actuator and should be left alone. 港口被給貼標籤幫助港口2也是將提供進入的途徑的一港口推進當時壓力,但是它通常連接支路閥門作動器並且應該被單獨留下。
- Water flow rate through terminal devices in an air condition water system with a single pump is controlled by the bypass valve when the air conditioning system is under part-load. 部分負荷時,單式泵變流量空調系統通過旁通閥控制流經末端設備的水流量,旁通流量的確定是正確選擇旁通閥的前提。
- Install valve in the direction of the flow arrows on the valve body. 按照閥體上的箭頭方向安裝閥門。
- Assigning the ideally fitted wedge, ground and lapped, to proper valve body. 將研磨后的楔板分配到最適合的閥體上。