您要查找的是不是：
- The bezel is also modified to act as a tachometer. 小張同學是南京曉庄學院電子商務專業大三女生。
- The rotating bezel now functions as it should. 鍥而不捨，金石可鏤。
- Remove the bezel and rubber gasket from the motor output shaft. 從馬達輸出軸上拆卸玻璃框和橡皮墊圈。
- Portable: LCD and Keyboard bezel of computer in view when opened. 攜帶型:打開后見到的LCD和鍵盤面板.
- Depress switch mounting tabs to remove switch from bezel. 降低開關裝置設定，以從玻璃框移去開關。
- Remove the ash receiver from the instrument panel center bezel. 從儀錶板中部玻璃罩拆下煙灰缸。
- Gap between hood and rear bezel is 0.03 inch maximum. 3上蓋及面板銜接縫隙應以0.;03英寸為最大。
- No bezel included in the package for mounting on chassis. 沒有面板包中包含用於安裝在機箱。
- Engineers systematically verify the smooth operation of the rotating bezel. 工程師們對旋轉表圈的運轉順暢性能進行綜合檢測。
- Flush mount using bezel or screw or rail mount to DIN 46 277 using base mount. 使用面板齊平安裝或螺釘或鐵路掛載到標準46 277基地安裝使用。
- Table size is measured from bezel point to bezel point; the average of four measurements is used. 表大小是衡量從面板點左邊框點;平均4個測量器.
- Features translucent case and colorful band, 3 hand movement, and unidirectional timing bezel. 愛炫愛酷趕時尚的你怎麼能錯過呢！
- Remove the two bezel screws, two latch screws, and one handle screw from the glove box inner door panel. 從手套箱內門板上拆下兩個前蓋螺釘，兩個鎖閂螺釘和一個把手螺釘。
- Insert a thin-blade tool under the edge of the transmission shift indicator bezel and pry up to remove. 在變速箱變速桿指示器擋板下插入一個尖頭工具，向上撬並拆去它。
- Pressure gauges in our standard range with triangular bezel or front mounting flange. 三角企口溝緣或前固定法蘭的標準壓力表。
- A unidirectional bezel only turns one way to prevent any danger of false manoeuvre. 單向表圈只能朝一個方向轉動以防止發生錯誤操作。
- Remove the two bezel screws, two latch screws, and one handle screw from the glove box inner door panel . 從手套箱內門板上拆下兩個前蓋螺釘，兩個鎖閂螺釘和一個把手螺釘。
- The bezel set Diamonds are Round Brilliant cut, SI1-SI2 clarity, G-H color and weigh 1.10 Carat Total Weight. 包鑲的圓形明亮式切割的鑽石，凈度為SI1-SI2，顏色為G-H，總重量為1.;10克拉。
- To do this, remove the 4 rubber pieces on the screen bezel, beneath them are screws.. 要做到這一點，刪除4橡膠件在屏幕上的面板，下面是螺絲.
- To use the Timing Bezel:Rotate the bezel counter clockwise until the O on the bezel lines up with the minute hand. 使用表面計時錶圈（時間讀取裝置）：逆時針旋動表圈，直到表圈上的O標記對準分針。
