您要查找的是不是：
- A foresaid structure made ASA had high notched Izod impact strength which was as high as 33kJ/m2. 上述結構賦予ASA以高抗沖性能,其缺口衝擊強度最高可達33 kJ/m2。
- The Izod impact strength, the bending strength and tensile strength were tested. 同時,測試了該材料的衝擊強度、彎曲強度和拉伸強度。
- It has been found that the notched Izod impact strength of the blend first decreased slightly and then increased with the addition of UFPR. 研究發現,隨粉末橡膠用量增大,共混物的衝擊強度先有所降低然後逐漸上升。
- The notched Izod impact strength of alloy increases with the increasing of EMG content in the condition of keeping other mechanical properties. 而隨著EMG含量的增加，材料的衝擊強度顯著提高，且其它的力學性能基本保持不變。
- When EMG was 9 phr, the notched Izod impact strength of the prepared alloy with high rigid, high toughness was 5.5 times as that of PPS. 當EMG含量為9份時;製備的高剛性、高韌性合金在保持其它力學性能基本不變的情況下其衝擊強度提高了4.;5倍;
- With the content of 5%wt ultrafine calcium carbonate, tensile strength of PP is 33.68MPa, tensile modulus is 1.38GPa, izod impact strength is 9,38KJ/m2. 超細碳酸鈣改性聚丙烯時，在5%25wt左右力學性能達到最佳，拉伸強度可以達到33.;68MPa，彈性模量可以達到1
- Theshrinkage rate is decreased by 25%and the izod impact strength of the composite isincreased by 13.8%.Which is demonstrated by examining the broken surface of specimen withSEM. 衝擊強度提高了13.;8%25，同時填充體系的成型收縮率較ABS下降了25%25。
- When the content of the COPA is 4%, the blends have the maximum izod impact strength and the tensile strength is nearly unchanged, POM/COPA blends have better mechanical properties. 當COPA含量為4%25時,共混物缺口衝擊強度達到最大值,拉伸強度幾乎不變,POM/COPA具有較理想的綜合力學性能。
- It was incorporated into PVC with barium stearate,and the heat stability and mechanical property were comprehensively studied by Congo red method,Tension test and izod impact strength test. 並將它與硬脂酸鋇復配添加到聚氯乙稀(PVC)中,通過剛果紅試紙法、拉伸試驗及衝擊試驗等多種方法對其PVC復配系統的熱穩定性能及力學性能進行了綜合研究,並確定了復配的最佳用量。
- When the total content of SBS and MBS was kept unchanged, the notched Izod impact strength of PVC/SBS/MBS blend increased with the increase of the content of MBS, and the transparency of the blend... 當SBS和MBS的總量不變時,隨著MBS相對含量的增加,共混體系的缺口衝擊強度逐漸增加,透光率在m(MBS)/m(SBS)=20/80時達到最大值,光學透明性能最好。
- The dependence of properties on the amount of the prepolymeric activator was also examined.It was shown that Izod impact strength of the material containing 8% prepolymer was the best. 討論了各種因素對製備過程的影響，並測試了製品性能與預聚作用量的關係，當預聚作用量為聚合作重量的8%25時，材料缺口衝擊強度最高。
- Plastics--Determination of izod impact strength 塑料懸臂樑衝擊試驗方法
- Standard Test Method for Determining the Izod Impact strength of Plastics 塑料衝擊強度測定的標準試驗方法
- Testing method for izod impact strength of glass fiber reinforced plastics 纖維增強塑料懸臂樑衝擊試驗方法
- Keywords Nylon 6;compatibilizer;blend;Izod impact strength;toughening; 尼龍6;增容劑;共混合金;缺口衝擊強度;增韌;
- Determination of izod impact resistance. 英文名稱： Styrene plastics.
- Keywords toughening;Izod impact strength;fracture surface;crystallite morphology; 增韌;缺口衝擊強度;斷裂形貌;結晶形態;
- The Izod notched impact strength of PMMA modified by ACR increased by 42.42% when the ACR mass fraction was 5%. 當ACR質量分數為5%25時，改性PMMA的缺口衝擊強度比未改性的提高了42.;42%25。
- notched Izod impact strength 缺口衝擊強度
- 1.When the content of the COPA is 4%, the blends have the maximum izod impact strength and the tensile strength is nearly unchanged, POM/COPA blends have better mechanical properties. 當COPA含量為4%25時,共混物缺口衝擊強度達到最大值,拉伸強度幾乎不變,POM/COPA具有較理想的綜合力學性能。
