您要查找的是不是：
- Hard-nesses are Brinell Hardness Numbers. 硬度是布氏硬度.
- The Brinell hardness number of the hot rolled plates varies with measurement on the different batch of the products. 通過對熱軋中厚板在不同深度上進行布氏硬度的測定 ,表明測量深度對硬度的明顯的影響 ,並指出獲得穩定值的必要性。
- The piece of cap is made from high heat-resistant material with good heat capacity, and Brinell hardness number in 180 to 135. 帽件由有良好熱容的高耐熱材料製成，且材料的布里涅爾硬度指數在180到135之間。
- Carbide balls are usually recommended for Brinell hardness numbers greater than 500. 在布氏試驗中碳化物質地的球通常在載入500千克以上時使用。
- In order to revise national standard of Metallic Materials-Brinell Hardness Test, the Brinell hardness numbers of specimens with different thickness are determined. 為修訂金屬布氏硬度試驗方法國家標準,測定了不同試樣厚度的布氏硬度值。
- 8. Hard-nesses are Brinell Hardness Numbers. 硬度是布氏硬度.
- 3.Hardnesses are Brinell Hardness Numbers. 硬度為布氏硬度.
- Brinell hardness number 布氏硬度數
- The Brindle hardness number (HB, formerly BHN) is defined as the ratio of the load P to the curved surface area of the indentation. 布氏硬度值（HB,之前寫作BHN）按照載入物在凹口的曲面區域的比值來定義。
- Method of measurement uncertainty evaluation for Brinell hardness test results was introduced in the present work. 文章介紹了布氏硬度試驗中測量結果的不確定度評定方法。
- The brinell hardness and the compressive properties increase with TiN content increasing. 其布氏硬度和壓縮強度隨TiN含量的增加而增大.
- An investigation was made on brinell hardness test with a universal material testing machine. 根據布氏硬度試驗的原理 ,提出一種在萬能材料試驗機上進行布氏硬度試驗的方法。
- It is improved on a basis of HBE-3000.It serves to measure the Brinell hardness of ferrous metals, non-ferrous metals. HBE-3000A電子布氏硬度計 Model HBE-3000A Electronic Brinwll Hardness Tester 該硬度計是HBE-3000的改進型，適用於測定黑色金屬，有色金屬的布氏硬度。
- The Vickers hardness number is indicated by HV ( formerly, DPH ). 維氏硬度用HV表示（之間寫作DPH）。
- The test results shows that there is a linear relationship between Brinell Hardness and the machinability of cast iron with homogeneous microstructure or tiny carbides. 經測試發現，鑄鐵的組織均勻和碳化物細小時，其布氏硬度與機械加工性能之間呈線性關係。
- It was found that the surface roughness is significant in Brinell hardness testing, but has little influence on Rockwell hardness. 結果表明,表面粗糙度對布氏硬度值有重要影響,而洛氏硬度值與表面粗糙度關係不大。
- In this paper the Brinell hardness of differently hardening titanium under loads 3000Kg HB(3000) and 1500Kg HB(1500) are measured. 本文測試了不同硬度鈦在3000公斤和1500公斤負荷下的布氏硬度值HB_(3000)和HB_(1500)。
- The Rockwell and Brinell hardness of 16 metals were investigated. The effects of surface roughness on the hardness values were discussed. 本文通過對16種金屬材料布氏和洛氏硬度的測試,討論了表面粗糙度對它們的硬度值的影響。
- Basic principle and content in standard ASTM E10-01 standard Test Methods for Brinell Hardness of Metallic Materials were described in this paper. 介紹了ASTM金屬材料布氏硬度試驗方法並與相應的國家標準進行了比較。
- HBE-3000 Electronic Brinell Hardness Tester with 10 steps testing force is able to measure hardness values with each 10 Brinell hardness scales. 電子布氏硬度計具備了10級試驗力，可分別測試布氏硬度的10種標尺。
