您要查找的是不是:
- The fit-lost condition in gear mesh is analysed, and the relationship between tooth drum guantity of Klingelnberg Spiral bevel gear sysytem and tooth plate eccentricity is derived. 分析了齿轮副啮合中的失配现象,并推导了克林贝格螺旋锥齿轮副轮齿的鼓形量与刀盘偏心距之间的关系。
- bevel gear mesh adjusting gasket 锥齿轮啮合调整衬垫
- bevel gear mesh 锥齿轮啮合
- A Simulating Analysis Model for Spiral Bevel Gear Meshing in Aerostat Reducer 航空减速器弧齿锥齿轮啮合仿真模型
- Gleason spiral bevel gear cutter. 格里森螺旋伞齿轮铣刀。
- The teeth on the gears mesh as they turn round. 转动时齿轮上的齿与齿相啮合。
- "The differential case supports the differentail-pinion gear on a shaft, and this gear meshes with the two bevel gears." 差速器壳支承在行星齿轮轴上,行星齿轮与两个半轴齿轮相啮合。
- Our main products: reducer, gear motor, bevel gear, worm-gear motor, cycloidal reducer and variator. 公司主要产品有:齿轮减速机;蜗轮蜗杆减速机;螺旋伞齿轮减速机;摆线针轮减速机及无级变速器。
- The result indicates that the two-terminal bracing structure is optimum for bearing load and gear mesh. 计算结果表明:主动齿轮轴两端支撑结构对轴承受力和齿轮啮合最有利。
- The parametric modeling method for loxodrome normal circular-arc spiral bevel gear was presented. 给出了斜航式法向圆弧螺旋锥齿轮的参数化建模方法。
- The inferential reasoning based on the mathematical model of straight bevel gear mating surface in project application. 推导基于工程应用的直齿圆锥齿轮啮合面的数学模型。
- Spur gear (SGA) or compound bevel gear (BGA) attachments can be provided in any position shown in Figure 1. 如果采用正齿轮(SGA)或复合伞齿轮(BGA)附件,则可以在图1中显示的各个位置安装手轮。
- The theoretical analysis research of spiral bevel gear lapping with dynamic force is carried out. 该研究是国内首次对螺旋锥齿轮动态力研齿进行的理论分析研究。
- All valves can be furnished with handwheels, chainwheels and bevel gear handwheels and chainwheels. 所有阀门都可以配置手轮、链轮和锥齿轮手轮和链轮。
- Designed with a base mount and removable top blocks, once installed in the vehicle and the gear mesh is set you can remove and reinstall the motor without resetting the mesh. 设计基地,山和移动大厦顶端,一旦安装在汽车和齿轮啮合是设置,您可以删除并重新安装电机不需要重新主题词。
- Bevel gears: gears which connect two shafts at right angles. 伞齿轮:连接直角相交两轴的齿轮。
- The teeth on bevel gears can be straight, spiral or hypoid. 锥齿轮的齿可以是直齿、螺旋形或准双曲面。
- Above result revealed that multidirectional closed die forging of spiral bevel gear was feasible. 揭示了使用复动闭式模锻模具成形小锥角螺旋伞齿轮的可行性。
- The gears mesh with each other. 齿轮相互啮合。
- Priciples of cutting epicycloid bevel gear by continuous indexing method are investigated systematically. 对摆线齿锥齿轮连续分类法铣齿原理进行了系统研究。