您要查找的是不是：
- The bending radius of the hose fitting should not be too small. 软管接头部位转弯不要过小,应大于软管内经8倍以上。
- The bending radius should not less than 15 times of cable diameter. 电缆弯曲半径:不小于电缆外径的15倍。
- The bending radius should not be less than 25 times of the cable diameter. 电缆弯曲半径：不小于电缆外径的25倍。
- TUBE DIAMETER SHALL BE WITHIN 10% OF NOMINAL DIAMETER WITHIN BEND RADIUS. 管直径须在直径理论值和折弯半径的10%25以内。
- Feature: Anti-bending of hose body, small bending radius, good stiffness, with or without metal fittings available. 特性:管体耐曲挠、弯曲半径小、挺性好。带或不带金属接头。
- Allowed bending radius not smaller than 6 times of its outer diameter, laying temperature not lower than 0. 电缆允许弯曲关径应不小于电缆外径的6倍,敷设温度应不低于0。
- The bending radius of a cable should not be less than 10 times of the cable diameter. 电缆弯曲半径不小于电缆外径10倍。
- The bending radius reduces with increasing length of the mainstream line, and then tends to be relatively stable. 随主流线长度增加，弯曲半径不会无限制减小，将会趋于某一相对稳定状态；
- Excellent pliability, flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性,可用于弯曲半径较小的场合。
- Permissive bending radius of cable should be no less than 20 times of external diameter of cable. 3电缆的允许弯曲半径不小于电缆外径的20倍。
- Small bending radius, simplified busbar framework, clear arrangement, easy mounting. 弯曲半径小，母线架构简明，布置清晰，安装方便。
- Excellent pliability，flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性，可用于弯曲半径较小的场合。
- For the same amount of bending angle, the springback increase linearly with the increase of bending radius. 对于一定的弯曲角度，零件端部回弹量随弯曲半径的增加而线性增加；
- The temerature not less than O℃ and recommended bend radius not less than6 times of outer dia. 电缆适用于管道地埋及架空敷设，不能承受机械外力作用。
- Bend radius of the bottom cover will need to be made smaller so that the two parts of the unit fit together correctly. 底盖的半径要改小一些，以便该产品的两个部分正确地合在一起。
- The bending angle of the conduit shall be at least 90 degree. The bending radiu shall be at least 6 times of the conduit outside size. 5电缆管弯曲角度不应小于90度；弯曲半径不应小于管子外径的6倍。
- Cycle Life Corrugated metal hose bend radius and minimum acceptable cycle life design requirements are outlined. 循环寿命-波纹金属软管的弯曲半径和可接受的最低寿命周期设计的大纲要求。
- In the previous works only the uniform wall-thickness elbows were studied.However, the elbow thickness is varied with the bending radius and ellipticity on the cross section. 以往对弯头的研究只考虑壁厚均匀不变的情况，但是实际上弯头的壁厚是沿着弯曲半径变化的，并且弯头的截面也具有一定的椭圆度。
- The transfiguration of effective index method(EIM) is used to analyze the factors influencing the losses, and the minimum bending radius and the relative losses are calculated. 根据有效折射率的变型形式分析了影响弯曲波导损耗的主要因素,并计算了最小弯曲半径及其相对应的损耗。
- At last, the formulation of allowable minimum bending radius limiting the change of the tube-wall thickness is derived, and proved to be of practical value. 推导出限制弯管壁厚变化量的许用最小弯曲半径公式,经试验验证具有一定的实用价值。
