您要查找的是不是：
- Free Float Type Steam Trap 浮球式疏水阀
- Inverted bucket type steam trap 倒吊桶式疏水器
- Upright bucket type steam trap 浮桶式疏水器
- A new type of thermostatic steam trap is designed with shape memory alloy(SMA). 利用形状记忆合金的功能特性设计了一种新型的热静力式蒸汽疏水阀;
- Steam Trap Leak Detection Programme. 蒸汽管网疏水阀检测,避免蒸汽泄漏及能源损失。
- Pressure gauges shall generally be bourdon tube or bellows type. 现场压力表应通常是波登管或波纹管型。
- The steam trap shall be a Watts Regulator Company Series G, MG, float and thermostatic type. 这种疏水阀应该是美国瓦茨调节阀公司系列G,MG浮子和恒温疏水阀。
- The steam trap shall be a Watts Regulator Company Series WIB. 这种疏水阀应该是美国瓦茨调节阀公司系列WIB产品。
- Only valves such as packless diaphragm or bellows type should be used. 只能使用无衬垫膈膜阀或波纹管阀。
- Replace the cover and the radiator steam trap has been repaired. 重新安装上盖子，这样散热器疏水阀就维修好了。
- Clear pipe line with pressurized steam before installation steam trap. 安装疏水阀之前应用带压蒸汽吹扫管道。
- The inverted bucket steam trap shall be installed as indicated on the plans. 在计划要求的地方应该安装反向桶型疏水阀。
- The key factors affecting the stagnation point position of L-type pipeline section are the setting position of bellows type expansion joint and the bend angle degree. 影响水平转角管段驻点位置的主要因素为波纹管补偿器设置位置、弯头角度。
- Pilot operated valves shall be considered for back pressures greater than 40% of set pressure if more favourable de-rating factors result in a valve smaller than a bellows type. 如果更多有利的非测定因子导致阀门小于波纹管类型的，对于背压大于设定压力的40%25的，应考虑辅助操作阀。
- Shaft sealing adopts single (double) face, bellow type mechanical seal, it also can adopt soft packing, is can meet sealing demands of all kinds of conditions. 轴封采用单（双）端面、波纹管等形式的机械密封，也可采用软填料密封，能适应各种条件下的密封要求；
- G series of orveheat steam trap,Utilizing the principle of buoyance,auxiliary valve can fluctuate in the pipe mouth . 系列过热蒸汽疏水阀采用集水池的方式，副阀利用浮力原理，可以在进气管口上下浮动。
- The Steam Trap stays closed until the steam cools enough to turn into condensate. 这时疏水阀就处于关闭状态，直到蒸汽足够冷却到凝结为凝结水。
- Its structure,operational principle and technical keys of the nonvalve shaft SMA steam trap are described. 论述了这种新型无阀杆疏水阀的结构、工作原理和技术关键;
- The calculation of stagnation point position of straight pipeline section with both movable ends and L-type pipeline section with bend at one end and bellows type expansion joint at other end is discussed. 摘要探讨了两侧为活动端的直管段及一侧活动端为弯头，而另一侧活动端为波纹管补偿器的水平转角管段驻点位置的计算。
- Balanced bellows seals may be required instead of conventional type due to process fluid considerations. Pilot operated valves are acceptable in place of bellows type for clean services. 出于对工艺介质的考虑，平衡波纹管密封可能要求替代常规类型。对于洁净用途，允许用辅助操作阀替代波纹管类型。
