您要查找的是不是：
- Spindle bearing bore diameter mm 轴端轴承规格
- Sprindle front bearing bore diameter 主轴前端轴承孔径
- Single plane mean bore diameter deviation. 单一平面平均内径偏差。
- Bore diameter variation in a single radial plane. 单一径向平面内径变动量。
- bearing bore diameter 轴承内径
- The size identification for Y-bearing units is the bore diameter of the incorporated Y-bearing. Y-轴承单元的尺寸代号表示所含Y-轴承的内径。
- The bore diameter and width of the IR inner rings are made to Normal tolerances in accordance with ISO 492:2002. 根据2002年的ISO 492标准,IR内圈的孔径和宽度以普通级公差制造。
- The tested solenoid has a bore diameter of 400 mm, stored energy of 0.445 MJ and a peak field of about 5 T. 被试磁体内径400mm、储能0.;445MJ;峰值磁场约5T
- There are no many vessels whose bore diameter is small in the root, and no ray in the xylem. 根中导管数量少，孔径小，次生木质部不含射线。
- Haha...I see u bully bear bear liao...u want me to tell Angel.... 人总会有自己的梦想，只要跟着梦想走，梦想一定能成真。
- The influence of throttle bore diameter and melt temperature in internal ladle on constituent distribution, marco-structure androckwell hardness of the casting was investigated. 研究了节流孔径和内浇包熔体温度两个工艺参数对铸件的成分分布、宏观组织和洛氏硬度的影响。
- Vsing this tool to process small bore diameter chilled steel,not only has high process accuracy,stabilizes process quality,but also raises tools using lifetime. 采用此刀具加工小直径淬火钢内孔,不仅加工精度高、加工质量稳定,又能大大提高刀具的使用寿命。
- By means of calculating the shafting torsional strength, a decision of replacing the main shaft by new one, whose bearing diameter is increased, was made reasonably and duly. 通过对轴系扭振强度计算，科学及时地作出了更换主轴的决定，并适当加大了新主抽抽颈直径。
- Next year the beared bear will bear a dear bear in the rear. 明年,长胡子的熊将在后方产一个可爱的小熊崽。
- Bearings up to and including 300 mm bore diameter are produced to higher precision than the ISO Normal tolerances. 孔径达(含)300mm的轴承的制造,使用比ISO正常公差更高的精确度。
- Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。
- Using this model, the paper studies the affection of the change of the bore diameter in each feature section to the initial velocity of projectile, and the relationship between the initial velocity of projectile and the total change of the bore diameter. 并用该模型研究了各特征截面内径改变量对弹丸初速改变量的影响,以及弹丸初速改变量与总内径改变量间的关系。
- The deformation matrix method is a fast and available method to calculate surface deformation of connecting rod bearing bore. 变形(柔度)矩阵法计算连杆轴承孔表面变形快速、有效；
- The attenuation coefficient of the dominant mode is less than 1 dB/m when the dielectric material is polyimide and the depth is 0.05 mm,which is far less than that of the same bore diameter metal circle waveguide for THz radiation. 得出其主模在THz频段的衰减常数小于1 dB/m,该值远小于相同内径的金属圆波导在这一频段的衰减常数。
- Position and start new bearing in bearing bore by hanNote that pilot bearing has seal at one enInstall bearing so seal is facing outward toward transmission. 用手定位并在内孔中试转新轴承。注意导向轴承的一端有密封件。安装轴承时使密封件向外对向变速箱。
