您要查找的是不是：
- battery cable clamp 电池线夹头
- Disconnect and isolate negative battery cable. 断开并隔离负极电池电缆。
- Analyzed the crack appearance of the cable clamp, amend unreasonable of mold gate, and solved the crack problem. 对电缆夹使用过程中断裂现象进行了分析,对模具浇口进行了改进,最终解决了问题。
- Connect battery cables positive first. 连接电瓶电缆，先连接正极电缆。
- Route the power cable between the power disconnect switch and the melter and through the cable clamp.Tighten the cable clamp. 安装连接电源开关与喷胶机的线路并装上电缆夹，再固定电缆夹。
- Insert the cable wire into the socket, clean up battery cable wire, close the battery slot cover, fasten screws, the process is finished. 把电池排线插入对应插座,整理好电池排线,盖上电池盖,拧紧螺丝,完毕。
- After the backing is pried up a little bit, take a small razor or flathead and pop the battery cable clip up to remove the Battery cable. 看图就知道,前后面板之间有两条带状线连接(这就是第一步说不要用力过猛的原因,你要太猛线就有可能出现损害)两根线,一根是电池的,一根是耳机接口
- To introduce a number of solar photovoltaic systems project: such as network controller, inverter, battery, battery cable, and junction box into the zone. 四是引进一批太阳能光伏发电系统配套项目：如并网控制器、逆变器、蓄电池、电池线、接线盒等。
- Warning:(RIsk of electrical shock or short circuit.)Use the cable clamp that is provided or use electrical conduit to protect the power cable from the sharp edge of the conduit knockout. 警告：（注意电击或短路）使用提供的电缆夹，或者使用电管道来保护电力电缆在管道尖处不受损。
- Disconnect battery cable. 拆下电瓶电缆。
- By analyzing on the structure of cable clamp and pressing process, the solution is proposed, the bending-reshaping-trimming compound die is designed, the die structure and work process is stated. 通过对电缆夹结构和冲压工艺进行分析,提出解决方案,设计了弯曲、整形、切边复合模,并阐述了模具结构及工作过程。
- Development of steel cable clamp on the cable crane 缆索起重机钢缆特制索卡的研制
- Rescuers need to make sure they don't cut the pressurized gas canisters that would inflate an airbag, or the battery cables in a hybrid. 救援人员需要确保他们不会切到受压的汽油罐，那样会导致气囊充气；
- Used for connection of cable clip, cable clamp, ect 用于电缆卡子、管缆卡子其它的连接
- DO NOT ALLOW JUMPER CABLE CLAMPS TO TOUCH EACH OTHER WHEN CONNECTED TO A BOOSTER SOURCE. 在连接到一个增压器源时，千万不要让跨接线组夹相互接触。
- The wood is held in position by a clamp. 木头用钳夹固定住了。
- Finally，the location on installation of cable clamps and unstressed length are calculated according to geometric form of free-cable. 最后，根据空缆形成后的线形计算索夹安装位置和吊索的无应力长度。
- Based on structural characteristics and forced conditions of steel cable, a new pair of steel cable clamps have been designed and made. 基于钢丝绳的结构特点及受载情况,设计制作了一种新型钢丝绳夹具。
- It calculates the main cable，suspender and other components in unstressed length，and initial installation location of the main cable and cable clamps. 计算主缆、吊索等部件的无应力长度和主缆、索夹的初始安装位置。
- The calculator needs a new battery. 计算器需换新电池。
