您要查找的是不是：
- Forward needle valve positions for easy access. 针形阀位置提前,便于接近。
- Unused taps shall be plugged with bar stock plugs. 暂时不用的取压口应棒料丝堵密封保存。
- Attach vent (yellow) hose to TC#4 and vent needle valve. 连接排气（黄）软管到测试旋塞4号和排气针形阀上。
- Open TC#3, needle valve "B ", and vent needle valve. 开启测试旋塞3号，针形阀“B”，和排气针形阀。
- Open TC#2 and needle valve "A", close needle valve "A" and TC #4. 开启测试旋塞2号和针形阀“A”，关闭针形阀“A”和测试旋塞4号。
- Close needle valve "A" high side (red) and open test cock No. 2. 关闭针形阀“A”高端（红），并开启测试旋塞2号。
- All needle valves must be closed on test kit. 检测组件上的所有针形阀必须关闭。
- Open vent needle valve and bleed air from hose. Then close vent valve. 开启排气针形阀，并从软管排放空气。然后关闭排气阀。
- Open vent needle valve fully until dripping from vent connection stops. 完全开启排气针形阀直到从排气连接处的滴漏停止为止。
- These lifts are ideal for long or wide loads such as lumber, sheets, pipe, bar stock and long assembles. 该升降台可用于升降诸如木料、平板、管子、棒料和长型设备，有着非常理想的使用效果。
- The engine is made entirely from bar stock and is Gerhard Spielmann's own design. 发动机是完全从酒吧股票和总理的斯皮尔曼是自己的设计。
- Open test cock No. 2 and needle valve "A" high side (red) on test kit. 开启测试旋塞2号和检测组件上的针形阀“A”高端（红）。
- Let us assume that a part spent 50 hours from the time it arrived at a plant as a rough casting or bar stock to the time it was a finished product. 让我们假设，一个部分花费50个小时的时间到达工厂作为一个粗略的铸造或酒吧的股票时，这是一个成品。
- Before starting test all needle valves must be closed. 在开始检测之前,所有阀门都必须关闭。
- Before starting test, all needle valves on test kit must be closed. 在开始检测前,检测组件上的所有针形阀都必须关闭。
- Needle valves have NPS / internal pipe threaded ends. 针形阀配置NPS内管螺纹连接端口。
- Open needle valve" A" high side and vent needle valve to vent air from bypass hose. 开启针形阀“A”高端和排气针形阀，从旁路软管排放空气。
- Please quote the parts attached. And please quote them in 2 ways, 1. forging+machining 2. machining from bar stock or tube. I will analyze the results, and recommend them the final customer. 请给附上的部分报价。请以两种方式报价：1.锻件和加工2.......我将分析结果并推荐给最终客户。
- Open needle valve "B" low (blue) very slowly until the differential gauge needle starts to drop. 很慢地开启针形阀“B”低端（蓝），直到压差表指针开始下降为止。
- Once mounted you now have a subassembly that you can mount to your fuselage.Spacers can be made from hardwood dowels (3/4" to 1") or machined aluminum bar stock to adjust your down and side thrust. 万一需要垫高引擎的时候.;可以使用硬木或者是铝柱去调整引擎的右偏角跟下偏角。
