您要查找的是不是:
- axial pressure angle 轴向压力角
- The results show that the axial pressure profile and voidage profile are uneven. 试验主要是测量沿床高的静压分布,然后根据压差法计算沿床高的空隙率分布。
- For the purpose of comparison,the triaxial test method with unchanging side pressure,and increasing axial pressure are else experimented in parallel. 为了比较,对保持侧压,增加轴压的常规方法也进行平行试验。
- Generally, standard gear hobs are only used to machine gears with the same modul, pressure angle as hobs themselves. 在一般条件下,标准齿轮滚刀只能加工与其模数、压力角相同的同制齿轮。
- This kind of axial pressure gauge is well suited for measuring those gases or liquids which will neither explode, nor crystallize, nor precipital, nor corrode with copper alloys. 该系列压力表用于测量对铜合金无腐蚀性、无爆炸性、且不结晶、不沉淀的气体或液体。
- Different from traditional electric and pneumatic screwdriver tools, this screwdriver system can adjust the screw with no axial pressure when driving screws. 区别于现有的电动、气动螺丝刀工具,该螺丝刀系统在驱动螺丝时,能对螺钉头实现无轴向压力的调节。
- Furthermore, the models for the analyses, such as pressure angle, curvature, kinetostatics, and input torque, of the mechanism are built. 且建立该凸轮机构之各项特性分析的数学模式,包括压力角分析、曲率分析、运动静力分析,及推导系统输入扭矩表示式。
- This paper deals with measuring the diameter of addendum circle for a involute spur cylindrical gear and calculating and determining its mode number and pressure angle. 本文阐述了渐开线直齿圆柱齿轮齿顶圆直径的测量与齿轮模数、变位系数、压力角等参数的确定方法和步骤.
- This kind of axial pressure gauge is well suited for measuring those gasses of liguids which will neither explode nor crystallize,nor presipitate,nor corrode copper copper or copper alloys. 该表用于测量对铜和铜合金无腐蚀性、无爆炸性、且不结晶踢,不沉淀的气体或液体的压力。
- It is confirmed that the sinusoidal gear can be easily undercut with a specific addendum height value decided only by the design pressure angle of the gear. 经讨论和仿真证实;正弦齿条所生成的齿轮在一个特定的齿顶高下最容易发生根切;该齿顶高数值只取决于正弦齿轮的设计压力角.
- With cylindrical coordination,this paper establishes the contour surface equations and pressure angle formula of the conical grooved cam with translating conical roller follower. 借助柱面坐标,建立了圆锥滚子直动从动件圆锥槽凸轮的廓面方程和压力角公式。
- Regarding the linear buckling mode as the initial geometrical defect of the structure, the stability nonlinear analysis of composite case under axial pressure was made by means of the finite element method. 利用有限元结构分析法,引入线性屈曲模态作为结构的初始几何缺陷,对复合材料壳体的轴压稳定性进行了非线性分析。
- In accordance with the characters of end section involute of helicoids,it is analyzed of change of the base circle affecting the pressure angle of involute profile. 依据渐开螺旋面端面渐开线的性质,分析了渐开线基圆变化对渐开线齿形压力角影响。
- Abstract: The present paper analyzes the axial pressure of the coil,the working principle of the coil drum and causes of slide scar on the strip head and advances the new method for the taper control of the coiling tension. 文摘:针对单机架平整机的带钢头部滑伤问题,分析了钢卷径向压力、卷筒的工作原理,及带钢头部滑伤形成原因,提出了卷取张力采用锥形控制的新方法。
- Effects of the axial pressure difference, the wall roughness, the length-diameter ratio and the inlet prerotation on the dynamic coefficients of finite-length concentric AFLGA are also discussed. 同时还讨论了壁面粗糙度、轴向压差、长径比及入口预旋等参数对大间隙环流动特性系数的影响。
- Accordingly,the least teeth number without undercutting is also decided only by the design pressure angle of the gear,without any relation to the coefficient of addendum height of the gear. 相应的无根切最少齿数也仅取决于正弦齿轮的设计压力角;而与齿顶高系数值无关.
- It is indicated through the analysis of assistant steering mechanism of the farm transporter model FR1608 that within th e rang e of standard swinging of the pitman arm, the design rod structure satisfies the requirement of optimum pressure angle. 对FR1608运输车转向助力机构的分析结果表明,在转向器转向垂臂的标准摆动范围内,设计参数满足最佳压力角要求。
- The method and procedure of measuring and calculating involute spur gear geometrical parameters such as tip diameter, module, modification coefficient and pressure angle were shown in this paper. 本文阐述了渐开线直齿圆柱齿轮顶圆直径及齿轮模数、变位系数和压力角等参数的确定方法和步骤.
- The motorcycle V-belt continuously-variable transmission controlled by centrifugal ball is analyzed, and the method to obtain the pressure angle of the wimble surface on the moving disk is gained. 摘要通过对采用离心球控制的皮带传动的摩托车无级变速器的分析,得到了可以确定移动盘内锥面压力角的方法。
- The tandem die is adopted and the axial pressurization technique is emploged in this die, thus the conditions of bellow moulding is greatly improved, the data of bellow moulding technique is obtained. 该模具采用分层分瓣凹模,并引入轴向加压工艺,改善了成形条件,并用它成功地制造了波纹管,得到了有关成形工艺参数。