您要查找的是不是:
- The axial internal clearance of the double row bearings is at least 0,5 mm. 双列轴承的轴向内部游隙为至少0,5毫米。
- SKF four-row tapered roller bearings are delivered as ready-to-mount bearing units with an axial internal clearance adapted to the actual application. SKF四列圆锥滚子轴承作为快装轴承装置供应,轴向内部游隙根据实际应用调节。
- The bearing sets of standard metric bearings are produced with the axial internal clearance provided in table 2 as standard. 标准公制轴承构成的轴承组在生产时带有如表2所列的标准轴向内部游隙。
- SKF double row tapered roller bearings of the TDO and TDI configurations generally have an axial internal clearance which is appropriate to a given application. TDO和TDI配置的SKF双列圆锥滚子轴承通常有适合特定用途的轴向内部游隙。
- SKF four-point contact ball bearings are supplied with Normal axial internal clearance as standard, but some sizes are available with greater or smaller clearance, or with reduced clearance limits. SKF供应的标准四点接触球轴承是带普通级径向内部游隙,但有些规格可带较大或较小游隙或降低的游隙范围供货。
- Axial internal clearance in upper half of C2 range 轴向内部游隙在C2范围的上半部分
- Axial internal clearance smaller than Normal 轴向内部游隙小于普通级
- Axial internal clearance in lower half of Normal range 轴向内部游隙在普通级范围的下半部分
- Partial and One-piece Measurement of Axial Internal Clearance for Four-row Tapered Roller Bearings 四列圆锥滚子轴承轴向游隙的分体与整体测量
- axial internal clearance 轴向内余隙
- Axial displacement of one ring relative to the other will gradually reduce the radial internal clearance in a CARB bearing. 一个套圈相对于另一套圈的轴向位移将逐渐减小CARB轴承中的径向内部游隙。
- This might lead to reduced internal clearance (fig). 这可能导致内部游隙减少(图17)。
- C3 radial internal clearance to ISO 5753:1991 (table 2). 标准C3径向内部游隙符合ISO 5753:1991(表2)。
- The reduction in radial internal clearance, or the axial displacement of the inner ring on its tapered seating is used as a measure of the degree of interference. 缩小径向内部游隙或内圈在圆锥座上的轴向偏移被用作调整过盈配合程度的手段。
- The reduction in radial internal clearance, or the axial displacement of the inner ring on its tapered seating is used to determine and measure the degree of interference. 径向内部游隙的减小值、或内圈在其圆锥轴颈上的轴向位移,被用来判定和测量过盈量。
- The narrow cam rollers have C3 radial internal clearance as standard. 标准的窄凸轮滚子有C3径向内部游隙。
- The values for the radial internal clearance conform to ISO 5753:1991. 径向内部游隙的数值符合1991年的ISO 5753标准。
- Vibration, interface fits and temperature can also affect internal clearance. 振动,温度和接口符合也会影响内部清除。
- It looks like I should specify an approximate 30 micrometer internal clearance. 看起来我应该定义一个大约的 30毫米以内的间隙。
- Therefore, under dynamic loads wear is naturally produced which enlarges the internal clearance. 因此,在动负荷下,很自然会发生磨损,从而增大内部游隙。