您要查找的是不是：
- austenitizing holding time 奥氏体化保温时间
- Here, cooling time is defined as holding time. 在这里，冷却时间定义为保压时间。
- The austenitizing temperature should be determined according to the Cr content and thickness of the casting, and the holding time should be calculated according to the modulus of the casting. 奥氏体化温度根据含铬量和铸件壁厚决定,保温时间根据铸件模数计算。决定加热升温速度应考虑铸件的结构、壁厚、铸态组织和炉内不同部位的温度差等因素。
- A variable displacement pump could save energy during the long holding time. 变量泵可在长的保压时间内节省能源。
- Holding time is determined by the solidification time of the gate. We decide it according to the weight. 保压时间的确定以浇口冷凝为依据。通过产品称重来确定。
- Attention: The holding pressure will affects the holding time. The higher holding pressure the longer holding time. 注意:保压压力会影响保压时间的长短。保压压力越大保压时间越长。
- A holding pressure unit allows the pre-plasticizer or a reciprocating screw to plasticize during the long holding time. 保压装置使预熔器或往复螺杆在冗长的保压时间内加料。
- To attain the similar max load stress, the holding time of PCH process was shorter than HP. 相同烧结温度和烧结压力的条件下，要想获得可承受近似压力的试样，PCH过程的烧结时间远远短于HP过程。
- The effect of holding time on intergranular phase and mechanical property of GPS silicon nitride ceramics was studied. 研究了保温时间对气压烧结(GPS)氮化硅陶瓷晶界相及力学性能的影响。
- The effects of stressing rate,holding time and loading path on ratcheting were discussed in the paper. 揭示了材料在不同加载速率、不同保持时间以及不同加载路径下的棘轮变形特性。
- The plasticized melt accumulates in front of the plunger. Only during injection (including holding time) is plasticizing stopped. 已塑化的熔融累积在注射柱塞的前面。只是注射时(含保压)不加料。
- The optimum concentration of Changcheng 3# or Lan-826 was 0.3%, acid pickling temperature was 60? and its holding time was less than 5 hours. 长城3%23或兰-826的最佳添加量为0.;3%25，最佳酸洗温度为60℃，酸洗时间小于5h。
- The hold time is the amount of time a router treats a neighbor as reachable and operational. 保持时间是路由器把一个邻居视为可以到达和操作的一段时间。
- The relation between survivors of microorganisms and processing pressure as well as holding time during UHP treatment to Kiwi juice was investigated. 探讨了热敏性纯猕猴桃汁在超高压处理过程中,存在的菌落总数和大肠菌群数随压强大小和加压时间变化的关系。
- The result indicates that under different quenching temperature and holding time , the formed bainite morphology are different. 结果表明,在不同淬火温度和保温时间下形成不同的贝氏体形貌。
- If EIGRP does not receive a packet from a neighbor within the hold time, EIGRP considers that neighbor down. 如果EIGRP在保持时间内没有从一个邻居那里收到封包，EIGRP会认为那个邻居是当掉的。
- When the hold time expires, DUAL is informed of the topology change, and must recalculate the new topology. 当保持时间终止时，DUAL会被告知拓扑已经改变，并且必须再重计算新拓扑。
- The influences of foaming and holding time on bubble diameter and the property of devitrified foam glass have been studied. 介绍了梯温炉的结构及原理,根据测量结果绘制了发泡温度与泡径的关系曲线。
- Then the temperature is higher than 10 degrees for charring, long holding time, and then formed with graphite structure (conductive) of charcoal. 再经温度高于1000度以进行炭化，保温时间特长，然后形成带石墨结构(导电)的木炭。
- The result shows that the void content decreases while the crystallinity and the tensile strength increases with the increase of the holding time. 研究结果表明,随着保温时间的增加,复合材料的空隙率降低,结晶度和强力增加;
