您要查找的是不是:
- welding motor generator 电动旋转式电焊机
- motor generator arc welder 电动发电机式直流弧焊机
- The paper introduced the process with argon arc welding of tungsten electrode to repair turbine rotor of1# generator system. 本文主要介绍了我厂利用钨极氩弧焊将1%23电机组汽轮机转子修复的工艺过程。
- For Automatic Welding-Electric Arc welding goggles and ccd imaging system. 用于自动变光电焊焊接护目镜以及看焊缝的ccd成像系统。
- Corrosion resistance and high strength. Argon arc welding of aluminum alloys. 耐蚀,强度高。铝合金氩弧焊用。
- Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。铜合金氩弧焊及钢的堆焊用。
- A CAD system of AC arc welding transformers called AWVTCAD was studied. 本文对交流弧焊变压器的计算机辅助设计系统进行了研究,简称“AWVTCAD”,结果表明利用该系统对弧焊变压器设计,不仅能提高计算精度与速度,而且也减轻了设计者的劳动强度及降低设计成本。
- It is perfectphase trigger circuit for arc welding power source of scr. 该相控触发电路是晶闸管整流弧焊电源的理想触发电路。
- Perhaps I need to pull apart another SCR and try the arc welding approach. 也许我需要把除了另一可控硅和审判电弧焊接的办法。
- Use manual metalic arc welding, the type of electrod is A102 for material 304. 设备采用手工电弧焊,304材质焊条牌号为A102。
- Arc brazing has the characteristics of braze welding and arc welding. 电弧钎焊是近十年来才发展起来的一种新型硬钎焊工艺,兼有钎焊和电弧焊的特点。
- Such as electric arc welding, carbon dioxide gas shielded arc welding, TIG etc. 如:电弧焊、二氧化碳气体保护焊、氩弧焊等各种焊接。
- This paper introduces a digital control system for submerged arc welding (SAW) applicable to various sorts of welding rectifier and feed wire device droved by direct current motor. 介绍一种埋弧自动焊数字控制系统设计,适应于各种焊接整流器和直流电机驱动的送丝机构。
- Motor Generator 1 is the engine starter, generator, and transmission ratio control. 电动发电机1发动机起动机,发电机,和传动比控制。
- Setting up a switch each one of arc welding generator, length of line can't exceed 5 meters , the length of line two times can't exceed 30 meters , the circuit is required intactly. 电焊机每台设置一个开关,一次线长度不得超过5米,二次线长度不得超过30米,线路要求完好。进出线端头应压接牢固,并安装可洗防护罩,焊机设置点应防潮、防雨、防砸和专人负责管理。
- The ship power-station is composed of dc voltager-stabilized power supply、 electric motor、 generator、 distributor and load. 电站系统主要由直流电源、流电动机、步发电机、配电盘和负载五部分组成。
- The problems of the peculiarities of arc welding and the estimation of weld quality are discussed. 主要考虑了弧焊特性的提取以及焊接质量的估计。
- The etched section also reveals that multiple weld passes were made over the top of the original submerged arc weld pass. 从酸蚀断面还可以看出:在原自动埋弧焊的上面覆盖有多层焊道。
- Re-melding in Ar arc welding of camshaft is particular heat treatment for hardening. 凸轮轴氩弧重新熔化硬化是一独特的热处理方式。
- Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys. 良好的耐蚀性、可焊性及塑性。铝合金气焊、氩弧焊用。