您要查找的是不是：
- amorphous filler metal 非晶钎料
- Study of microstructure of vacuum brazed-joints of amorphous filler metals 非晶态合金钎料真空钎焊接头组织研究
- Aerospace series - Gold base alloy AU-B40001 - Filler metal for brazing - Wire. 航空航天系列.;金基合金AU-B40001
- They are readily weldable, in most cases, with or without filler metal. 多数此种合金可焊（不论加或不加焊料金属）。
- However, for attaching nonpressure parts to pressure parts, the filler metal chemistry shall match the nominal chemistry of the pressure part. 但将非受压元件焊接受压元件时所用的填充金属，应与受压元件的标称化学组成相配。
- Influence of Sn and In in silver filler metal on spreadability and joint strength is studied. 研究了银基钎料中元素锡、铟对钎料铺展性能和接头的影响,分析了钎料的显微组织和锡、铟在钎料中的作用机理。
- Cold lap is a condition where the weld filler metal does not properly fuse with the base metal or the previous weld pass material (interpass cold lap). 冷隔？（未熔合）由于熔敷金属没有很好的与母材熔合或没与前道焊缝熔合（层间未熔合）。
- Abstract: In this paper, the mechanism of electrochemistry corrosion of the tractor radiator brazed with brass (H90 and H70) and Sn-Pb filler metal was investigated. 文摘:研究了采用黄铜(H90、H70)和锡铅钎料钎焊而成的拖拉机水箱电化学腐蚀机理。
- It adopt advanced jointing technique when joint the valve and the copper tube，it brazing filler metal well，without pore and overheating，and has a smooth make and break . 阀体与铜管的连接，采用先进的焊接工艺，钎料到位，无气孔和过烧现象，开闭灵活。
- The mechanical properties of welding and weldment have been conduct on X80 pipeline steel under the selection of welding process, welding filler metal and parameter. 摘要在选定焊接方法、焊接材料和工艺参数条件下，进行了X80管线钢试件焊接和接头性能试验。
- Spot checks contractor piping isometrics or fabrication drawings showing weld procedures， filler metal， pre-heat and post-weld heat requirements and monitors their use. 抽检承包商的管道轴侧图和预制图中关于焊接程序、填料、预热和焊后热处理的要求并监督其实施情况；
- In this paper, the mechanism of electrochemistry corrosion of the tractor radiator brazed with brass (H90 and H70) and Sn-Pb filler metal was investigated. 研究了采用黄铜(H90、H70)和锡铅钎料钎焊而成的拖拉机水箱电化学腐蚀机理。
- To join(metals)by applying heat, sometimes with pressure and sometimes with an intermediate or filler metal having a high melting point. 焊接通过加热，有时加压或有时用媒介物或有很高熔点的填充金属来连接（金属）
- To join(metals)by applying heat,sometimes with pressure and sometimes with an intermediate or filler metal having a high melting point. 焊接通过加热，有时加压或有时用媒介物或有很高熔点的填充金属来连接(金属)
- A storage cell in some amorphous memory devices. 某些非晶体存储器中的一个存储单元。
- THE PRESENT SITUATION AND ANALYSIS OF EXTRUSION TECHNOLOGY FOR BRAZING FILLER METALS IN THE WORLD. 国外硬钎料挤压技术的现状与分析。
- Requests to use filler metals manufactured to other standards must be in writing and approved by SECCO prior to use. 使用按其它标准生产的填充金属，必须事先提出书面申请，并获得赛科公司的批准。
- For welded seams in clad material, filler metals selected from the following table shall be used. 对于复层上已焊过的接缝应从下表选用填充金属。
- The brittleness of brazed seam for nickel-base brazing filler metals is always paid close attention. 镍基钎料的钎缝脆性问题，一直是人们关注的研究课题。
