您要查找的是不是：
- Determination of the basic size of cam mechanism with oscillating follower based on the allowed pressure angle 按许用压力角确定摆杆盘形凸轮基本尺寸
- Analytical Solution for Determining Basic Size of Mechanism with Follower Cam Based on Allowed Pressure Angle 按许用压力角确定推杆凸轮机构基本尺寸的完全解析法
- The Determination of a Cam's Allowable Pressure Angle 凸轮许用压力角的合理确定
- allowed pressure angle 许用压力角
- Designing the Geometrical Amounts Oscillating Follower Cam Mechanisms in Accordance with Allowable Pressure Angle 按许用压力角确定摆动从动件凸轮机构的几何尺寸
- A Right Method for Determining the Minimum Size of a Disc Cam with a Translating Follower by Allowing Pressure Angle 按许用压力角确定直动推杆盘形凸轮机构最小尺寸的正确解法
- THE ANALYTICS FOR DESIGAING MINIMUM SIZE OSCIUATING FOLLOWER DISC CAM MECHANISM IN ACCORDANCE WITH ALLOWABLE PRESSURE ANGLE 按许用压力角设计最小尺寸的摆动从动杆盘形凸轮机构的解析法
- allowable pressure angle 许用压力角
- Generally, standard gear hobs are only used to machine gears with the same modul, pressure angle as hobs themselves. 在一般条件下，标准齿轮滚刀只能加工与其模数、压力角相同的同制齿轮。
- Furthermore, the models for the analyses, such as pressure angle, curvature, kinetostatics, and input torque, of the mechanism are built. 且建立该凸轮机构之各项特性分析的数学模式，包括压力角分析、曲率分析、运动静力分析，及推导系统输入扭矩表示式。
- This paper deals with measuring the diameter of addendum circle for a involute spur cylindrical gear and calculating and determining its mode number and pressure angle. 本文阐述了渐开线直齿圆柱齿轮齿顶圆直径的测量与齿轮模数、变位系数、压力角等参数的确定方法和步骤.
- It is confirmed that the sinusoidal gear can be easily undercut with a specific addendum height value decided only by the design pressure angle of the gear. 经讨论和仿真证实;正弦齿条所生成的齿轮在一个特定的齿顶高下最容易发生根切;该齿顶高数值只取决于正弦齿轮的设计压力角.
- With cylindrical coordination,this paper establishes the contour surface equations and pressure angle formula of the conical grooved cam with translating conical roller follower. 借助柱面坐标,建立了圆锥滚子直动从动件圆锥槽凸轮的廓面方程和压力角公式。
- In accordance with the characters of end section involute of helicoids,it is analyzed of change of the base circle affecting the pressure angle of involute profile. 依据渐开螺旋面端面渐开线的性质，分析了渐开线基圆变化对渐开线齿形压力角影响。
- Second, there is a leak in the system that is allowing pressure to bleed off when the unloader is put in bypass. 第二，系统泄露，以至于在减压器安置在旁路时压力被释放。
- No one is allowed to get his ticket out of turn. 任何人都不准不按次序买票。
- Flashes are not allowed to be used in this museum. 这个博物馆里不准使用闪光灯。
- The relative factors are discussed:maximum allowable pressure inside the site, permeating coefficient of of MSW,bio-gas production rate, diameter of the well, etc. 同时讨论了影响控制范围的各主要因素：垃圾层中最大允许压力、垃圾层的透气性能、垃圾的产气速率等。
- The road is too narrow to allow the passage of gondola. 这条街太窄，大型货车不能通过。
- Accordingly,the least teeth number without undercutting is also decided only by the design pressure angle of the gear,without any relation to the coefficient of addendum height of the gear. 相应的无根切最少齿数也仅取决于正弦齿轮的设计压力角;而与齿顶高系数值无关.
