您要查找的是不是:
- It is believed that the interphase is responsible for transferring the stress from one adherend to another in adhesive bonded joints and is frequently the site of environmental attack. 在粘接接头中应力通过界相从一侧被粘接体传递到另一侧被粘接体,而且界相最易受环境影响而导致粘接失效,因此界相对粘接接头的性能,如强度、刚度、耐候性等起着非常重要的作用。
- single-lap adhesive bonded joint 单搭胶接接头
- Estimating the Percentage of Wood Failure in Adhesive Bonded Joints 胶粘连接时对木材破坏百分率的估算
- Whether the adhesively bonded joints keep good vacuum tightness after experiencing repeatedly cooling and heating is an important factor that determines the durability of non-magnetic Dewar. 粘接接头在经历反复冷却、复温后能否保持良好的真空密封性,是决定无磁杜瓦耐用性的一个重要因素。
- adhesive bonded joints 胶接接头
- Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines 用于航空喷气涡轮机燃料管线的胶粘剂结合型玻璃纤维(玻璃纤维增强热固树脂)管及管配件标准规范
- Standard Specification forFiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type Epoxy Resin, for Condensate Return Lines 用于冷凝回流管道的胶粘剂结合型环氧树脂玻璃纤维(玻璃-纤维-增强热固树脂)管及管配件标准规范
- Keywords Adhesively bonded joints;Lap length;Stress distribution;Finite element method;Adhesive fillets; 胶接接头;搭接长度;应力分布;有限元法;胶瘤;
- NUMERICAL ANALYSIS OF THE EFFECT OF LAP LENGTH ON THE STRESS DISTRIBUTION OF ADHESIVELY BONDED JOINTS 搭接长度对胶接接头工作应力分布影响的数值分析
- Fracture of adhesively bonded joints and discussion of relative fracture criterions 胶接接头断裂及相关断裂准则探讨
- Experimental Study on the Deformation and Damage of Composite Adhesively Bonded Joints and Bimetal Solder Film 复合材料胶接及异材焊接界面形变与断裂的实验研究
- The reason of the failure of epoxy bonded joint in water was that the epoxy adhesive on the metal surface was substituted for water. 环氧胶接接头在水中破坏失效的原因主要是渗入到胶接层的水分子取代了胶粘水分子在金属表面的粘附。
- It introduces moist heat aging and sea - water proof tests carried out respectively on J - 71 adhesive and its complementary pliofilm J - 47A and J - 71 bonded joint. 介绍了对J-71胶及其配套胶膜J-47A,和对J-71胶胶接接头分别进行湿热老化试验、耐海水性能试验情况。
- It showed that the strength of adhesive bonded structure would not decrease with a volume decrease of 20%. 拓扑优化的结果表明:在体积减少20%25的情况下,胶接结构的强度不会降低;
- Keywords adhesively bonded joint;interface;weak interfacial film theory;wetting theory; 胶接接头;界面;弱界面层理论;润湿理论;
- The first requirement for any adhesive bond is that the adhesive most wet the substrate. 对所有粘结剂粘结的首先要求,就是必须能浸润基材。
- Reasons for quality problems of adhesive bond between cork sheets and composite cabin are analyzed. 分析了引起复合材料舱体软木粘贴质量问题的原因。
- Adhesively bonded joints 粘结节点
- Suitable for perforating,compounding,and slicing,stretch fabric,pure cotton and adhesive bonded plaster,being able to do single-side as well as two-side perforating. 适用于弹力布、纯棉布、无纺布药膏的打孔、复合、切片,可单面打孔,也可以双面打孔。
- The reason for reduction of bonding performance of epoxy bonded joint was the degradation of epoxy adhesive. 胶粘剂分子链的降解是环氧胶接接头胶接性能降低的主要原因;