您要查找的是不是:
- acid etch technique 酸蚀技术
- Visual inspection, SEM/EDS, XRD, oxalic acid etch test, oil extraction technique and oil composition analysis were undertaken determine the causes of the failed valve. 研究方法包括目视检查、SEM/EDS、XRD分析,并辅以不锈钢敏化试验及油渍萃取与成分分析技术,综合分析不锈钢阀门之材质劣化原因。
- Acid Etching Technique for Preparation of Mesoporous Composite Environmental Materials 制备介孔复合环境材料的酸洗刻蚀工艺
- Both finishes are equally corrosion resistant and they all give better corrosion resistance than bead blasting or acid etch. 翻译过来的大意是:两种处理方式(石洗和缎面)都有较好的抗腐蚀能力,它们的抗腐蚀能力要比珠光处理和酸蚀处理要好。
- Objective To observe the influence of acid etch and unacid etch of GIC on compression of composite resin glass ionomer cement filling. 目的 对玻璃离子粘固剂 (GIC)表面采用酸蚀刻处理与非酸蚀刻处理后形成的两组GIC 复合树脂复合体试件进行力学研究 ,以寻找良好的GIC表面处理方法。
- Stainless steels--10Percent oxalic acid etch test GB/T4334.;1-1984不锈钢10%25草酸浸蚀试验方法
- Effect of acid etching on electrical performances of microchannel plate[J]. 引用该论文 孙忠文;黄永刚;贾金升;黄英;刘淑慈;刘辉;李国恩.
- Ensure that substrate is mechanically scarified or acid etched prior to primer. 在底油涂层施工前,一定要确保用机械方法或酸液蚀刻方法对基层进行拉毛处理。
- Dow etching: A powerless etching technique for letter-press plates invented by Dow Chemical Corporation. 陶氏腐法:陶氏化学公司发明的一种无粉腐技巧。用来制造活版印版。
- Dow etching A powerless etching technique for letter-press plates invented by Dow Chemical Corporation. 陶氏腐法陶氏化学公司发明的一种无粉腐技巧。用来制造活版印版。
- It is necessary to measure Young's modulus of micro-mained materials because of the special manufacture process by using silicon etching technique. 摘要利用蚀刻矽技术制造的微机械构件,由于特殊的制作工艺而需要对其材料的杨氏模量进行测量。
- If concrete is heavily troweled (smooth/tight) surface may need to be acid etched. 如果混凝土表面非常密实,或已经过压光处理,则需要进行酸洗。
- Lising KOH anisotropic wet etching technique to obtain the V-shape structure of fiber array.This technique apply precrision alignment to control undercut effective. 利用KOH非等向性湿蚀刻技术,得到光纤阵所需之V型凹槽结构,并配合精确对准光罩之应用,有效控制侧蚀量,应用于光纤阵列晶圆制程技术。
- Using patented technology: acid etching process to make the blade of graters sharper. 本版权所有中华经贸网,任何人未经同意不得擅自引用!
- UHMWPE fiber were treated by chromic acid etching and chemical vapor depositing polypyrrole(PPy). 摘要采用铬酸刻蚀和化学气相沉积聚吡咯处理了超高相对分子质量聚乙烯(UHMWPE)纤维。
- By acid etching, the enamel was changed into a highly mineralized alveolar coarse surface, which was the key factor for achieve stable and reliable adhesion to resin. 牙釉质经酸蚀处理后,形成高度矿化的蜂窝状的粗糙表面,依靠微机械嵌合力与树脂形成稳定可靠的粘结。
- In this thesis, etched walls with verticality of better than 89? and Root-mean-Square (RMS) surface roughness of below 10 nm are achieved by using non-switched Inductivity Coupled Plasma (ICP) etching technique. 论文采用无切换的电感耦合等离子体刻蚀(ICP)技术在SOI材料上刻蚀出垂直度好于89°、均方根表面粗糙度小于10nm的刻蚀侧壁。
- Methods Thirty teeth were prepared and divided into three groups.One group was air abraded and was acid etched, another one was air abraded, and the other one was acid etched. 方法分别对30颗离体牙的牙釉质进行喷磨、喷磨加酸蚀、单纯酸蚀后粘结树脂,测定其剪切强度。
- It is necessary to measure the mechanical properties such as Yong's modulus of micro\|machined materials because of the special manufacturing process by using silicon etching technique. 利用蚀刻硅技术制造的微机械构件,由于特殊的制作工艺而需要对其材料的机械性能如杨氏模量等进行测试。
- The strength of chemical-strengthening glass is analyzed before and after surface acid etching, and the strength reservation of glass corroded is studied. 对离子交换增强玻璃表面不同程度酸腐蚀后强度变化的情况进行了分析,并对表面腐蚀后强度的保留进行了研究。