您要查找的是不是:
- Zn- Mg alloy coating 锌.;镁合金镀层
- The bond strength of Ni-P coating on Mg alloy AZ91D is studied with metalloscope,SEM,EDS. 利用金相显微镜、SEM、能谱仪(EDS),研究了镁合金AZ91D的化学镀Ni-P的结合强度。
- An uniform zinc phosphate coating was fabricated on the surface of AZ91D Mg alloy. 在AZ91D镁合金表面制备了细致均匀的锌系复合磷化膜。
- The tensile properties and corrosion resistance of hot dip 55%Al Zn alloy coating steel are investigated. 研究了热浸镀 5 5%25Al Zn合金镀层钢的室温拉伸性能和耐蚀性能。
- The hot dip Zn Ni alloy coating provides good anticorrosion performance. Two kinds of materials, Q235 and Q345 used for galvanizing Zn and Zn Ni alloy. 对Q2 35和Q345两种材料表面热浸镀纯Zn和Zn Ni合金 ,研究Ni对热镀锌耐蚀性的影响。
- The white corrosion products on hot dip Zn Al alloy coating exposed to seawater in dynamic aerated immersion were investigated by means of XRD and TEM. 采用XRD和TEM对热浸锌铝合金镀层在动态充气海水全浸试验时所形成的白色腐蚀产物进行了研究。
- The strengthening mechanism of Zn Al Cu pseudo alloy coating and relationship among hardness,aging temperature and time are studied by SEM,XRD,EDX and hardness test. 利用扫描电镜(SEM )、X射线衍射分析 (XRD)、能谱分析 (EDX)和硬度测试等手段 ,对涂层的性能进行了测试 ,分析研究了Zn Al Cu伪合金涂层硬度与时效温度和时效时间的关系 ,并探讨了强化机理。
- Using the FEM, the deformation and stress field of a large-scale Mg alloy die casting machine have been calculated by ANSYS. 摘要压铸机的整体变形情况对压铸机性能和铸件质量有重要影响。
- Because Mg alloy has a low density and good performance,it has an extensive development and application potentiality. 镁合金由于质轻、性能良好等特点而具有广阔的开发与应用潜力。
- The effect of mischmetal additions on the ignition temperature of ZM5 Mg alloy was investigated and compared with t. 针对ZM5镁合金,研究了混合稀土及其加入量对起燃温度的影响,并与纯稀土的阻燃效果进行了比较。
- Extrusion deformation can fine the grain of Mg alloy and increase its properties remarkably. 挤压变形可显著地细化镁合金晶粒并提高镁合金的力学性能。
- The results show that the room temperature yield strength and tensile strength of hot dip 55%Al Zn alloy coating steel are higher than those of low carbon steel (Q235) plates, and its elongation has not reduced. 结果表明 :Q2 35钢板经热浸镀 5 5%25Al Zn合金后的室温屈服强度和抗拉强度均高于Q2 35钢 ,而伸长率没有降低。
- The importance of studying the mold filling velocity of Mg alloy in the expendable pattern casting (EPC) process is pointed out in this paper. 消失模铸造的充型过程对于获得健全铸件至关重要,研究工艺参数对镁合金消失模铸造充型速度的影响,对于工艺参数的优化和铸件质量的提高具有非常重要的理论和实用价值。
- Since its chemical character is very active, Mg alloy is prone to oxidation and burning, which makes it impossible to be melted and cast in air. 但由于镁的化学性质活泼,非常容易氧化、燃烧,导致镁合金无法在大气条件下直接进行熔炼和浇注。
- In this paper, the adhesiveness and the corrosion resistance of hot dip Zn 0.1Ni alloy coating are studied by the bending test and the salt spray test and are compared with those of hot dip zinc coating. 通过弯曲试验和盐雾试验,研究了热浸Zn?0.;1Ni合金镀层的粘附性能和耐腐蚀性能,并与热浸锌镀层对比。
- The production technology for Mg and Mg alloy powders are:grinding milling,atomisation,melting and recycling,turning and chipping. 由于镁及镁合金的独特性能,其粉末及粉粒通常用球磨法、铣削法、雾化法生产,特别是铣削法用得最多。
- Abstract: The microstructure of AZ61 Mg alloy made by the methods of normal cast and twin-screw rheo-cast was investigated. 摘 要: 采用双螺旋流变铸造技术制备镁合金AZ61铸锭,并与常规铸造组织进行对比。
- The electrochemical behavior of AZ31 Mg alloy was investigated by measuring anodic polarization curves and electrochemical impedance spectroscopy(EIS). 采用阳极极化和电化学阻抗谱(EIS)技术研究了AZ31镁合金的电化学腐蚀行为。
- Using the FEM,the deformation and stress field of a large-scale Mg alloy die casting machine have been calculated by ANSYS. 压铸机的整体变形情况对压铸机性能和铸件质量有重要影响。
- The corrosion resistance of these coatings is better than that of mechanical Zn plating coating,especially CuNi alloy coating is the best. 这些铜及铜合金镀层的耐蚀性能皆好于机械镀锌层,尤以铜-镍合金镀层的耐蚀性能最高,提高15倍左右;