您要查找的是不是：
- Yield Strength Load Factor 屈服强度负载系数
- The load factor of the hashtable. 哈希表的加载因子。
- Returns the current maximum load factor. 返回当前的最大负载因子。
- Desirable properties for forming include low yield strength and high ductility. 令人满意的成形特性包含了低降伏应力和高延展性。
- When a task is enqueued, the load factor is increased. 任务排队时,加载因子将增加。
- A load factor of 1.0 Is the best balance between speed and size. 加载因子1.;0是速度和大小之间的最佳平衡。
- The load factor is the maximum ratio of elements to buckets. 加载因子是元素与存储桶的最大比率。
- Oxygen precipitates (useful for gettering) can reduce the yield strength (critical shear stress) up to fivefole. 氧沉淀(可用作吸杂)会使屈服强度(临界剪应力)降低为五分之一。
- The welder shall be capable of welding (full hard cold-rolled) steel with yield strength of up to 85Kg/mm2. 焊机应能焊(冷轧全硬)其屈服强度大于85Kg/mm2的钢带。
- The V-N microalloy steel with yield strength of 550 MPa is produced by EAF-CSP route. 目前,在EAF-CSP流程中通过V-N微合金化技术可成功生产屈服强度为550 MPa的高强度低合金钢。
- The hotel business has its own load factor in the form of the occupancy rate. 旅馆业本身的荷载系数由开房率来表示。
- The result show that the yield strength of the bars drop apparently and the tensile strength rise a little. 结果表明,自然时效后钢筋的屈服强度有较大幅度下降,抗拉强度有小幅度的上升。
- Oxgen precipitates (useful for gettering) can reduce the yield strength (critical shear stress) up to fivefole. 氧沉淀（可用作吸杂）会使屈服强度（临界剪应力）降低为五分之一。
- Change of molecular magnetic moment of motherliquor and shear yield strength are studied in magnetorheological fluid. 对磁流变液中母液分子在磁场作用下磁矩的变化以及由此引起的剪切屈服强度的变化进行了研究.
- Torque values listed are typical or alloy steel bolts (approximately 100,000 psi yield strength) used with carbon or intermediate alloy steel valves. 所列的扭矩值是标准值或适用于合金钢螺栓(屈服强度大约为100,000 psi),配置在碳钢或中间合金钢阀门上。
- Relationship between yield strength and near-neutral pH stress corrosion cracking resistance of pipeline steels-an effect of microstructure. 管道钢的屈服强度和抗近中性pH应力腐蚀开裂间的关系-显微结构的影响。
- Motley: I don't like guessing. Did you pull a load factor of 50% out of your butt? Where did that come from? motley: 我不喜欢猜测。你难道是从屁股里面把那个负荷指标标给拉出来的?这个究竟从哪里来的?
- Tensile and yield strength are determined by pulling a standardized machined sample in an tensile testing machine until the sample breaks. 抗拉强度和屈服强度的测定是在拉力试验机中将一个加工好的标准试样进行拉伸直至试样断裂。
- Load Factor The load factor is the ratio of the average load to the generator set power rating. 负荷系数负荷系数指的是机组的平均负荷与额定功率之间的比率。
- The output parameters of the model are three mechanical properties namely ultimate tensile strength (UTS), yield strength (YS) and elongation (ELO). 模型的输出为三个力学性能指标,即抗拉强度、屈服强度和延伸率。
