您要查找的是不是：
- Influence of Tension on Wall Thickness Distribution during Stretch Reducing of Seamless Tube 无缝钢管张减过程张力对壁厚分布的影响
- Analysis of Wall Thickness Distribution for Different Stretch-Reducing Pass by FEM 张力减径机不同孔型横向壁厚分布的有限元模拟分析
- Wall thickness distribution 壁厚分布
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- The effect of following variables on mould temperature distribution has been studied:casting speed,water velocity,wall thickness,scale deposition and galvanization layer. 讨论了拉速、冷却水流速、铜板厚度、水垢和铜板镀层对结晶器温度分布的影响。
- The ice thickness distribution map was obtained by hydrostatic equilibrium. 依据流体静力学平衡原理构建Amery冰架的冰厚度图,结合冰雷达测厚数据,获得了海洋冰的空间分布。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- On the other hand, the unequal thickness distribution of adsorption layer in tangential direction resulted in the size distribution of nanoparticles. 切线方向上吸附层厚度不等导致粒子大小的分布。
- In addition, using columniform punch and conical punch, different stress-strain distribution and thickness distribution at deformation region of flanging is compared. 通过采用不同凸模型式,比较了柱形凸模和锥形凸模翻边时变形区的应力应变及厚度分布的不同。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- In deferent inking system,the ink thickness distribution and the ink flow ratio is different for the deference of the number of roller and the arrangement of the roller. 同时,墨辊上墨层厚度及着墨率的变化与输墨系统的墨辊数量及排列方式均存在一定关系。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The liquid upward transport mechanism is very important for predicting the circumferential liquid film thickness distribution in horizontal gas-liquid annular flow. 为更为准确地预测液膜厚度，综合考虑了扰动波抽吸作用机理、气体二次流机理及液滴沈降和携带机理；
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- As to the flatness calculating of CVC mill, a software is developed to predict the strip thickness distribution after rolling by using the influence function method. 针对CVC热连轧精轧机组板形计算问题,采用影响函数法开发了计算热连轧机轧后板断面厚度分布的软件。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm，冷却时间便占10.;8秒。
- The analytic formula of the feeding zone thickness distribution in hydroforming of variational cross-section tube is derived by using the total strain theory. 摘要通过力学分析和全量本构方程，推导出了变径管内高压成形送料区壁厚增厚的解析公式。
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm，冷却时间是76.;8秒。
