您要查找的是不是：
- To produce CJ 3.6 tex in spinning frame with pneumatic V shape draft and guarantee yarn quality,processing of weight per 5 m,draft multiple of back area,roller gauge,top roller pressure,leading distance of front top roller an so on were optimized. 为了在气动V形牵伸细纱机上顺利生产CJ 3.;6 tex纱;保证成纱质量;对粗纱定量、后区牵伸倍数、罗拉隔距、胶辊加压及前胶辊前冲量等工艺参数进行了优化试验。
- Use ice do massage the back of hand between thumb and index finger(V shape). 在手背的拇指和食指中间的V字形的部分，用冰块来摩擦。
- From the inside corner to extend the line Yanshao, and Erjian a V shape. 从内眼角至眼梢的延长线，与耳尖构成V字形。
- The most optimistic outlook would be a ”V” shaped recovery in which growth plunges and then rebounds quickly. 最乐观的看法是呈V型复苏，即成长遽降，然后快速反弹。
- Carry on the craft reform to bearing seat and axis of the belt conveyer supporting roller. 对带式输送机的托辊的轴承座和轴进行工艺改革。
- A large deformation elastic plastic FEM model is employed to simulate the stretch flanging of V shaped sheet metal parts. 采用弹塑性大变形有限元方法研究了几何形状和材料参数对“V”型零件翻边的影响;
- Cast rubber supporting roller is adopted, driving is stable and can lessen abrasion of channel for roller with long service life. 采用铸胶托辊,传动稳定不打滑,并对辊体轮道减摩,寿命长。
- The basic load ratings given under the heading "Support roller" in the table section take this into account. 表中“支承滚子”标题下所列出的基本额定负荷考虑到这种情况。
- The method of using two right-and-left finial pedestal and one V shape pedestal was the best. 采用左右2顶尖座,再配一V形座附件是较好的一种方法。
- Lianxing was sharp and the V shape, the tone was a sharp sudden acute angle, formed from Wenduan to Erjian V shape. 脸形尖而呈V字形,口吻尖突呈锐角,从吻端至耳尖形成V字形。
- Complications rates of unstable trochanteric fractures treated with V shape nail and DHS were 27.2% and 19.4%, respectively. 不稳定型骨折中 ;V形钉组并发症为 2 7.;2%25;DHS组为 19
- All components of these support rollers can be mounted separately. 这些支承滚子的所有部件都可以分开安装。
- Tracking experiment of MIG on V shape welding groove is made with this method,and the experiment result validates the validity of this method. 利用该方法对V形坡口进行了金属熔化极气体保护电弧焊(MIG)的跟踪试验,试验结果验证了所用方法的有效性。
- The new mill is increased side supporting roller sets to form FFC mill and analysis of roller bear force and working roller steady condition and then gain calculation method of driving roller moment. 对轧辊进行受力分析和工作辊稳定条件分析，得到了驱动轧辊的力矩公式。
- The machine through mechanical transmission, the machine makes material in two asymmetry V shape cylinders to turn over to-and-fro. The purpose of uniform can be got. 该机通过机械传动，使两个不对称的V型圆柱体内的物料做往复翻动，达到均匀混合之目的。
- The components of the machine are frames, electrical roller, plastic belts and supporting rollers. 整机由机架、电滚筒、塑带、托辊等部件组成。
- Flat bed machines that are used to make ribbed knit fabrics having two sets of needles arranged to form a V shape with the open end of the V parallel to the base of the machine. 生产罗纹织物的横机有两组针,呈v型排列,v型的开口与横机的底座平行。
- Methods : to treat stenosing tenovaginitis with “V”shape acupotome combined with manipulation, and treat the disease with block therapy as contrast group at the same time. 方法：针刀组采用“V”形针刀对腱鞘狭窄处推切，术后结合手法充分松解腱鞘；同时与局部封闭疗法组进行了临床对照；
- Support rollers are basically needle or cylindrical roller bearings with a thick-walled outer ring. 支承滚子基本上是外圈壁较厚的滚针或圆柱滚子轴承。
- Four flying buttress shapes support a central vessel, which supplies hydrostatically pressured water to nozzles at the inner portion of the structure. 四飞行支柱形状支持一艘中央船,提供流体静力被迫使的水给喷管在结构的内在部份。
