您要查找的是不是：
- Uneven edge at front placket. 前筒反光。
- Info:Fabric: cotton canvas Zipper and button at front placket for CF closure Having several pockets E ...... 主要材质:棉次要材质:棉尺码:全码适用季节:冬
- A man-tapered shirt with yoke at front and back, a pointed collar, two patch pockets with flaps and fancy snap closures on front placket and cuffs. 前后幅都有育克的男装修长衬衫;尖领;两个有袋盖的明贴袋;且前中开口与袖口都以新潮按扣扣合.
- Please makw sure that pocket placement is even left to right , side to side , Pocket appears to be off by 1/8 inch, Slight puckering at front placket . 请确保口袋位置从左到右，边到边均分，口袋偏移了1/8英寸，前门襟有轻微起皱.;需更正后确认。
- Garment have uneven stitching width at front rise. 前浪缐步不平均。
- Uneven edge stitching on waistband. 裤头车线不均。
- Should be 1/4” double needle stitching at cuff ,armhole and front placket. 介英/夹圈及前筒应车1/4”双线。
- The curved edge at the junction of two intersecting vaults. 穹棱肋在两交叉的穹顶相接处的呈曲线状的边缘。
- Edge at the station, a Jiang Tabao up, turning laps. 在车站边上，一把将她抱起来，转了几圈。
- Please makw sure that pocket placement is even left to right , side to side , Pocket appears to be off by 1/8 inch, Slight puckering at front placket . Approve with corrections 请确保口袋位置从左到右，边到边均分，口袋偏移了1/8英寸，前门襟有轻微起皱.;需更正后确认。
- So we just take a quick look at front page. 因此我们只是快速的浏览一下第一版面。
- Know regulations about reception at front desk. 懂前台接待规则。
- You can change RMB at front desk. 您可以到前台去兑换人民币。
- Gusset 3" at front and 7" at rear. 衣袖在前面的3寸以及后面的7寸处。。。
- Waistband misaligned at front when buttoned . 裤头扣钮后前面不对称。
- For styles with front placket, verify that upper placket fully covers under placket. Open and check construction and stitching. 有前门筒的款式,门筒面层要盖住底层。打开并检查其结构和针步。
- Therefore, those evidences through field work support the result of marble being crust at front edge of marble intrusion, derived carbonatite. 因此，在野外宏观构造上得出支持此处大理岩是岩浆成因的结论。
- For styles with front placket verify that upper placket fully covers under placket. Open and check construction and stitching. 有前门筒的款式，门筒面层要盖住底层。打开并检查其结构和针步。
- Now each edge at the circled juncture has a corresponding edge to which it can be stitched. 现在环绕接合点的每条边都有对应的边进行缝合了。
- Molding ends or splices will be cut clean without jagged, sharp or uneven edges. 饰条的两端或接合处要裁切整齐，无锯状，无锋利以及边不平。
