您要查找的是不是:
- Stud Pull Die Bond Strength 柱螺栓牵引焊接模测量
- Methods: The bond strength of Au - Pt, Au - Pd, Ag - Pd and Ni - Cr alloys were determined by means of pull - through test. 方法:通过金瓷界面间的剪切强度测定,观察金铂合金、金钯合金、银钯合金及镍铬合金的金瓷结合强度。
- Figure 2 illustrates the fundamental aspects of a die bond. 图2所示为管芯连接的基本结构。
- Bond strength is an important parameter for wafer bond. 键合强度是关系到键合好坏的一个重要参数。
- The bond strength experiment of dogtooth exposed to pulsed Nd: YAG laser[J]. 引用该论文 朱建中;黄炜;许肖杰;林斌;陈钰清;顾锡荣.
- Xeno III Adhesive provides bond strength comparable to total etch systems. 异种三胶粘剂粘结强度可比提供总额蚀刻系统。
- Indirect methods to measure the interface bond strength include the interlaminar shear strength test. 测量界面粘结强度的间接方法包括层间剪切强度试验。
- Finally, the bond strength of FRP bars to epoxy resin and cement grout is also studied. 同时对纤维塑料筋与水泥装和环氧树脂的粘结强度也进行了探讨。
- Dicing Saw, Wire Bonder, Die Bonder and Spare Part... 划片机、焊片机、焊线机、上蕊机、封装等二手设备...
- Bond strength between tooth and base bracket with two bracket base designs: An in vitro comparative study. 两种底板托槽体外粘结强度的对比研究。
- The shear bond strength of titanium and its alloys with SOLIDEX veneering resin. 钛钛合金牙粘结复合树脂。
- The bond strength of Ni-P coating on Mg alloy AZ91D is studied with metalloscope,SEM,EDS. 利用金相显微镜、SEM、能谱仪(EDS),研究了镁合金AZ91D的化学镀Ni-P的结合强度。
- This product design for IC assembly die attache process on die bonder machine. 本产品为IC集成电路封装工艺芯片全自动固晶机上而专门设计。
- It can be concluded that the bond strength of Tyrian/One-Step Plus has a comparable high value under microtensile test. Tyrian/One-StepPlus黏结系统的黏结性能最好。
- This product design for IC assembly die bonding process on die bonder machine. 本产品是为IC封装自动贴片机及其贴片工艺而设计。
- Insulating ability and peel bond strength are two important properties for thermal insulating covering. 保温性能和剥离强力是保温被两个非常重要的性能指标。
- First, design die bond process because Film BGA substrate must overcome warpage issue, next, use TAGU-CHI DOE method, fillet height control was quality characteristic and optimal parameter design. 本文即先从黏晶制程的机台机构上,设计黏晶制程,克服基板翘曲的现象,再使用工业界常使用的田口式品质设计方法,将填充胶的控制列为品质特性,然后最佳化参数设计。
- Bond strength you can test up to through the use of the avulsing test, or test a consistent reference samples. 粘合强度可以通过采用测试盘进行剥离测试,或测试某个质量稳定的参考样本。
- Finally,the bond strength of FRP bars to epoxy resin and cement grout is also stu... 同时对纤维塑料筋与水泥浆和环氧树脂的粘结强度也进行了探讨。
- Bending strength, compressive strength, interfacial bond strength and frost-resistance are also studied and analyzed. 并对修补混凝土的抗折、抗压、新老界面粘结强度以及抗冻性等进行了试验研究。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries