您要查找的是不是：
- Seismic design calculation 抗震计算
- Seismic design of reinforced concrete and masonry buildings II. 钢筋混凝土和砌体结构的抗震设计2。
- Conventional seismic design is based on the rigid foundation assumption. 常规的抗震设计都是基于刚性地基的假定。
- The performance objective of three-level seismic design for multi-ribbed composite wall is classified in the light of the calculation of damage indices range to different damage levels. 最后给出了密肋复合墙体在不同震害等级时的损伤指数范围和墙体三水准抗震设计的地震损伤目标建议。
- A comparison table is made for API, CNS/ JIS, GB seismic design standards, and how to apply to the Taiwan area. 此外本文亦概要比较了当前各国(PI、NS/IS、B)震设计标准的内容，以及应用在台湾地区的使用方法。
- A comparison table is made for API, CNS/JIS, GB seismic design standards, and how to apply to the Taiwan area. 此外本文亦概要比较了目前各国(API、CNS/JIS、GB)耐震设计标准的内容，以及应用在台湾地区的使用方法。
- The seismic intensity ratifies according to jurisdiction regulated by the state as a criterion of local seismic design. 按国家规定的权限批准作为一个地区抗震设防依据的地震烈度。
- Designing calculation of furnace stack and nozzle is studied. 同时介绍煤气炉炉体和煤气喷嘴的设计计算。
- E.Rosenblueth,Optimum seismic Design of Linear shear Buidings[J]. J.Struct.div.ASCE.1976 STS,May. 王光远.;剪切型多层框架抗震设计的最优刚度分析[J]
- The article describes the system constitution and design calculation of oil film bearing lubrication system. 介绍油膜轴承润滑系统的系统组成和设计计算。
- Priestley, M.J.N., Seible, F., and Calvi, M.（1996）, Seismic Design and Retrofit of Bridges, New York: Wiley &Sons. 台湾省结构工程技师公会（2003），钢筋混凝土建筑物耐震能力评估手册，台北：科技图书。
- The analysis, improvement and design calculation of the screwy feed appliance of the flour packer was introduced. 对螺旋供料器应用于面粉包装机进行了分析，提出了改进措施及设计计算。
- It founds an analysis model and then does the mechanics analysis while doing the design calculation of the cross-axle. 建立了十字轴设计计算时的力学模型,并进行了力学分析;
- Priestley, M. J. N., Seible, F., and Calvi, G. M., "Seismic Design and Retrofit of Bridges", Jonh Wiley &Sons, New York, 1996. 范立础、卓卫东，“桥梁延性抗震设计”，人民交通出版社，北京，2001。
- By utilizing FEA application and experiments, design theory and design calculation method is tested. 利用有限元软件及实验对设计理论及设计计算方法进行了必要的验证；
- How to control the torsional response of structures under earthquake action is a problem frequently occurred in seismic design. 摘要如何控制结构在地震作用下的扭转作用是结构抗震设计中经常遇到的问题。
- There is a contrast between seismic design code of different countries because of economic condition and seismic fortification. 由经济条件和抗震设防思想存在差异,各国抗震设计规范中的规定也不尽相同。
- Abstract The design calculation and operating principle of the side jack sampler are described with some notes in its use. 介绍了侧向千斤顶式取样器设计计算、工作原理、使用注意事项。
- Paulay, T., and Priestley, M.J.N., Seismic Design of Reinforced Concrete and Masonry Buildings, John Wiley &Sons, New York, pp. 68-79 (1992). 蔡万来;921集集大地震建筑物破坏分析与对策;詹式书局;台北;第150-189页(2000).
- The structure and working principle of a screw tap holder is introdu- ced,and the design calculation of its main parts is presented. 介绍了快换丝锥夹头的结构、工作原理和主要零件的设计计算。
