您要查找的是不是：
- Bust dart seam allowance must be ironed upward. 胸折止口要烫向上面。
- The seam allowance can just be washed plain cotton sheeting. 接缝处（缝份）可以水洗？普通的棉布？
- Tear drop loop m/b tack down to seam allowance with bartack. 辫子耳仔要用打枣固定在只口上。辫子耳仔要用打枣固定在只口上。
- The width of the seam allowance used determines the width of the welt. 留出缝份,缝份的宽度根据贴边的宽度而定。
- In appearance, the welt seam is similar to the wrong side of the flat fell seam. join the fabric, right sides together, with seam allowance. 外观上与明包缝的反面相似。将纪念品物的正面合在一起缉缝。
- The seam is made with an underlay, which is cut to a width double that of the seam allowance. 这种缝需用垫层。垫层的宽度是缝份的二倍。
- Place the tape in the seam allowance area of the garment and catch one edge of the tape while stitching. 把贴带放在衣服的缝份上,缉缝时抓住贴带的一端。
- There are sample rooms, however, where an overall 1.3cm(1/2 inch) seam allowance is used. 然而有些样品室都用1.;3cm(1;2英寸)缝份。
- Trim the inner seam allowance to 0.6cm (1/4 inch) . the final stitch, encasing the trimmed. 修剪里层缝份;留0.;6cm(1/4英寸)。最后缉缝;对修剪过的缝封边;使这条缝饱满。
- Trace inside the roll line and remove the seam allowance from the front edge and peak of the lapel. 描出里面的翻领线,去掉门襟止口处尖驳头处的缝份。
- Cut this out on the cross from sew-in interfacing piece on the jacket front seam allowance. 用预先做好衬斜裁,其后把布放在前身缝份上。
- The French seam finish is no more than 0.6cm (1/4 inch); a 1.3cm (1/2 inch) seam allowance is advisable. 用来去缝是一种合适的缝型。来去缝的缝线不超过0.;6cm(1/4英寸)。1
- Fold under 0.6cm (1/4 inch) of upper seam allowance and stitch close to the folded edge. 上层缝份折0.;6cm(1/4英寸)紧靠边缉缝。
- Industrial block patterns usually have seam allowances added. 工业服装样板通常已加放缝份。
- Trace a further piece from the shoulder area by removing the seam allowance and extending the bottom-curved ling 2cm (3/4 inch) into the jacket front. 在前肩部位再做一片垫肩,方法是去掉粘合衬肩部缝份底部曲线延伸到前身2cm处。
- Just make sure to sew a wide enough seam allowance so they fusible doesn’t show through. 但是要确保缝合线有一定的宽度，这样融合带就不会露出来了。
- ON ALL SHEAR SLEEVES, THE ARMHOLE SEAM ALLOWANCE IS TO BE PRESSED FACING BODY, NOT THE SLEEVE. 所有剪刀袖（不知道是不是插肩袖），袖夹圈骨位止口倒向大身，不是倒向袖
- In appearance, the welt seam is similar to the wrong side of the flat fell seam. join the fabric, right.sides together, with seam allowance. 外观上与明包缝的反面相似。将纪念品物的正面合在一起缉缝。
- Use a 1.9cm (3/4 inch) seam allowance for a 1.3cm (1/2 inch seam finish and a 1.3cm (1/2 inch) seam allowance for 0.6cm (1/4 inch) seamfinish. 用1.;9cm(1/4英寸)缝份接缝为1
- Remove the darts and seam allowance from heavier interfacing before fusing, in order to reduce bulk. Fuse the interfacing to fabric. 为了减少臃肿,在粘合前把厚粘合衬的省道与缝份去掉,然后将衬布粘合到面料上。
