您要查找的是不是:
- Developing of Roll forging Die Softwre Under MFC MFC环境下辊锻模具软件开发
- Theoretical and Experimental Study of Roll Forging Die Design 辊锻模具设计的理论及试验研究
- Keywords file;tapered hexahedron;roll forging die and mold;conjugation;meshing; 锉刀;六方锥形体;辊锻模具;共轭;啮合;
- Comprehensive technical measures for prolonging the life of the hot press roll forging die 延长辊锻热成形模寿命的综合技术措施
- High Temperature Microstructure and Property of WC Ceramic Layer on Surface of Roll Forging Die by Powder Feeding Laser Cladding 辊锻模具表面送粉激光熔覆WC陶瓷层的高温组织与性能
- Application of Conjugation Principles in the Design of Roll Forging Dies 共轭原理在辊锻模具设计中的应用
- Geometrical Analysis For the Surface Contour of the Die Cavity and Forging in Roll Forging Dies 辊锻模型槽与锻件轮廓曲面的几何分析
- Roll forging die 辊锻模
- Design of a Composite Hot Forging Die for Screw Plugs. 油孔螺塞拼接式热锻模具的设计
- The productive process of performing forming roll forging technology of slip joint pliers is introduced. 介绍了锂鱼钳制坯一成形辊锻工艺的生产过程。
- Abstract The paper gives out structure of tilting pin type hydraulic forging die for producing frame of shaker. 给出了震动器机壳斜销式液锻模具设计结构。
- The article has described substance and its applicability of roll forging technology, advantages producing harrowing tooth with roll forging forming technology. 叙述了辊锻工艺实质及其适用性,用辊锻成形工艺生产耙齿的优点。
- The deformation and flow of metal in the process of roll forging are much different from those of ordinary die forging, So are the design of its technology, preliminary forming dies and dressing dies. 辊锻过程中金属变形及流动,与一般模锻工艺相比存在较大的差异,因而其工艺设计及初成形道次模具、整形模具设计也不同于常规模锻工艺。
- Through the analysis of hook, a reasonable forging process and forging die have been designed. The defects has been analyzed and solved. 摘要通过对吊钩的工艺分析,设计了合理的锻造工艺方案及其热锻模,并对出现的缺陷进行了分析解决。
- An investigation was carried out for the recondition of a mould for the forming of automotive plastic floor board and a half-axle swing forging die. 介绍了几种典型模具快速修复工艺方法,并对汽车地板革成形模和汽车半轴摆动辗压模的修复进行了研究。
- The dynamic stress concentration problems at the swallowtail on a hammer forging die are investigated by using the dynamic photoelastie method. 用动态光弹性法研究了锤锻模燕尾的动态应力集中问题。
- Traditional forging die manufacturing including a lot of process and using EOM to form the impression results some disadvantages such as longer production time and higher cost. 摘要传统锻模加工,由于加工道次多,且需采用放电加工制造模穴,导致有制造时间长,且成本偏高的缺点。
- This paper introduced the inserted forging die,and the difficult point of its plasticity design. The main point of its plasticity design which can enlarge its function. 简要地介绍了镶块锻模结构特点和可塑性优化设计的难点;着重介绍扩大其使用性能可塑性设计方法的要点.
- The life of H13 steel forging die for link was studied,the relation of die life and die rigidity was discussed, the measures of increasing die life were brought forward. 研究了H13钢连杆锻模的寿命问题,讨论了模具寿命与模具硬度的关系,提出了提高模具寿命的措施,设计了H13钢连杆锻模的最佳热处理工艺。