您要查找的是不是:
- Repeated cutting times 重复切削次数
- Abstract: In practical harvesting working, repeated cutting area, fail to cut area and one time cutting area are different because of abrasion of the cuter. 文章摘要: 在联合收割机收获作业中,由于往复式切割器不同程度的磨损,使切割图中重割区、漏割区及一次切割区的面积也在不断地发生变化。
- The growth rate and yield of triticale were decreased with the increase of cutting times. 小黑麦刈割次数的增加会造成生长速率的下降,产量降低。
- The influencing factors, including intensity of magnetic field, cutting times of magnetic lines and tempera ture of water, were studied. 对水磁化过程中,磁场强度、切割磁力线次数及温度的影响进行了研究。
- Automated case-handling systems at Smith's Dairy cut time to load trucks by 40 percent, improve efficiency. 奶制品厂在采用自动化包装箱搬运系统后,装车时间削减了40%25,生产效率提高。
- The net gain tillers decreased with cutting times increasing ,restraining tiller effect of higher cutting frequency strengthen year by year while lower cutting frequency weaken. 净分蘖数随刈割次数的增加而降低;高频刈割对分蘖的抑制效应逐年加强,低频刈割对分蘖的抑制效应逐年减弱。
- The 2 years comparative research of the net gain tillers, leaves regrowth and cumulative yield for perennial ryegrass under different cutting intensities and cutting times. 摘要对不同刈割强度和时间下,混播草地中多年生黑麦草净分蘖数和叶片生长季节动态及其年积累和年产量进行了2年的比较研究。
- Ice-cold watermelon on a steamy summer day really hits the spot. But you'll be best served by keeping it on your countertop until cutting time. 酷热的夏天吃冰冻西瓜当然是好享受.;但最好还是一直存放在桌上;不要冰冻的好
- He repeated several times that he was busy. 他一再说他很忙。
- Direct finishing, not only to save the expensive titanium alloy material, but also reduces tool consumption, shorten the cutting time, thereby reducing the cost! 直接精加工,不但节约了昂贵的钛合金材料,也降低了刀具消耗,缩短了切削时间,从而降低了成本!
- That is to measure changes in physical properties during milk coagulation process for defining the coagulation time and then the optimal cutting time of coagulum. 试验研究结果表明:超声信号的衰减与牛奶在凝固过程中的物理性能变化密切相关。
- In rough cut of NC milling of helicoid, there are many defects when the generic programming means, for example,longer cutting time,inefficient , exigent tools are used. 在螺旋曲面的数控粗加工中,采用一般的编程方法得到的刀具路径在实际应用中存在加工时间长、效率低、对刀具要求高等缺点。
- The influence of air cutting angle and air cutting time to chip breakage is studied quantitatively.The correctness of air cutting theory is verified by the experiments. 定量分析了间断切削过程中的空切角度、空切时间对断屑的影响,并通过试验验证了用空切理论分析断屑的正确性。
- The analysis indicates that tapping torque increases as net cutting time ratio increases,where net cutting time ratio influences the tapping torque more significantly. 结果表明,攻丝扭矩随净切削时间比的增加而增大,且对攻丝扭矩的影响最显著。
- I shall have to report you for repeated lateness. 你老是迟到,我可要告你了。
- He made a resolution never to repeat the act. 他决心不再采取那种行动。
- I was embittered by repeated failures. 我因屡次失败而苦恼。
- He repeated the joke but it missed fire the second time. 他把笑话又说了一遍,可是第二次就没有赢得笑声。
- Rose bushes shoot again after being cut back. 玫瑰丛修剪後还能再长出新枝。
- He repeated her statement word for word. 他一字不差地重复她的话。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries