您要查找的是不是:
- Ray bending angle 电波弯曲角
- The bending angle increases with an increase of the energy density. 增加能量密度,板料的弯曲角度显著增大。
- Feeding system adopts CNC servo motor, bending angle uses CNC control. 采用数控伺服电机进料系统,数控折弯角度控制系统。
- The angle that results when a light ray bends as it passes from one medium to another. 光线从一个介质到另一个介质时产生的角度改变。
- For the same amount of bending angle, the springback increase linearly with the increase of bending radius. 对于一定的弯曲角度,零件端部回弹量随弯曲半径的增加而线性增加;
- The temperature and the deformation fields of the forming process were calculated and the final bending angle was predicted. 计算了弯曲成形过程的温度场及变形场,预测了钢板的最终弯曲角度。
- The bending angle of the conduit shall be at least 90 degree. The bending radiu shall be at least 6 times of the conduit outside size. 5电缆管弯曲角度不应小于90度;弯曲半径不应小于管子外径的6倍。
- It shows that the depth rise and maximum width of backflow zone depend on froude number and bend angle. 根据能量和动量守恒原理,导出了计算上游水位壅高和下游回流区最大宽度的理论关系式,并用室内实验结果进行了验证。
- Under the constant bending times, the biggest bending angle can be obtained with an optimal accumulative line energy value. 在扫描次数一定的情况下,存在一个最优的累积线能量使弯曲角达到最大;
- The simulation value and test results of bending angle of the tube were compared and analyzed, which proved the validity of finite element model for the tubes. 通过对管件弯曲角度试验结果与模拟值的对比分析,证明了建立管件有限元模型的正确性。
- The atmospheric refractivity profiles below the height of the GPS receiver are obtained with this inversion technique, as well as the bending angle of rays. 将该反演方法应用于观测数据的反演,获得了观测点高度以下的大气折射率剖面,以及电渡弯曲角。
- The formulae for calculating the bend radius of neutral plane and the decrement of bend angle after springback were derived by considering the deformation after unloading. 依据卸载变形的分析计算,推导出回弹后中性层弯曲半径及弯曲角变化量的计算公式。
- The only requirement is that you look at road at near glancing incidence because the rays bend very gradually. 唯一的条件是要从接近掠入射的方向去看公路,因为光线弯曲得非常慢。
- The key factors affecting the stagnation point position of L-type pipeline section are the setting position of bellows type expansion joint and the bend angle degree. 影响水平转角管段驻点位置的主要因素为波纹管补偿器设置位置、弯头角度。
- A display device that uses a cathode ray tube. 一种使用阴极射线管的显示装置。
- Bending angle about material augments along with laser power and laser light spot diameter augment, but bending angle about material minishes along with laser scan rate and material hardness augment. 随着激光功率和激光光斑直径的增加板材弯曲角度增大,但随着激光扫描速度和板材厚度的增加弯曲角度减小。
- Special incline is not usually main function plane of pressing, its external shape size and bending angle are not dimensioned directly in 2D part drawing;the data needs calculating. 特殊斜面在冲压件中通常不是主要功用面,在二维零件图中,一般不会直接标注特殊斜面的外形尺寸及其弯曲角度,需要自行设法计算得到数据。
- Radioactive ray is material thing. 放射线是实际的物质。
- The plant was growing at an angle. 植物呈一定角度生长。
- A ray flower or the corolla of a ray flower. 舌状花舌状花或这种花的花冠