您要查找的是不是：
- SCH / PCB layout ECAD Tool skill is essential.5. 同时作为行业领先者，魏德米勒在电联接领域制订了全球通用的规范与标准。
- SCH / PCB layout ECAD Tool skill is essential. 同时作为行业领先者, 魏德米勒在电联接领域制订了全球通用的规范与标准。
- Master at least one PCB layout software, good at PROTELL is a plus. 精通C语言编程，具有良好的软件规范编程习惯。
- Provide direction to PCB designer on PCB layout design. 为印刷电路板设计员提供指导。
- The system design and the high speed PCB layout technology are discussed. 对系统设计和高速PCB设计技术进行了详细的分析。
- Double side probe plates:Test pads can bespread on both sides of PCB for convenient PCB layout. 上下针板结构：测试点可双面选点，方便电路板布线设计。
- Experience in PCB layout for home appliance or industrial products would be preferred. 具有小家电或工控板PCB布板经验者优先。
- SCH / PCB layout ECAD Tool skill, EMC knowledge, Safety Regulation Standards well understanding is essential. 目前魏德米勒集团公司在全球七十多个国家设有分公司、销售机构和代理商，拥有员工2300多人。
- DipTrace Schematic Capture and PCB Layout also support popular netlist formats and spice. DipTrace原理图捕获和PCB布局还支持流行的网表格式和香料。
- Good knowledge on PCB layout design in area of EMC, SI, RF, High-Speed &general digital and analogue design aspects preferred. 在印刷电路板设计,在电磁兼容性,硅,无线电频率,高速率,全电子化或者相类似的设计也可以
- We had to switch to BGA packaging to get stock, and made a new corresponding PCB layout (using the exact same schematics). 我们不得不换到BGA包装进行储备，所以后来做出了相应的新PCB电路板（用相同的电路图）。
- Typically, when creating a Net Class using a Blanket directive, you might also define PCB layout information to apply to those member nets within. 典型地讲，当使用覆盖区指示器创建一个网络类时，您也可以定义一个PCB布局布线规则信息到那些成员网络。
- Knowledge of PCB layout rule for manufacturing, proficient in Power PCB layout tool is must, other tools such as Protel is preferred. 五年以上音响产品电子设计经验及具备数字信号处理及分离设备的放大器的布线经验。
- SCOPE OF POSITION: (Why does the position exist)In charge of designing PCB layout and providing help on PCB rela...... ... 公司名称：环球迈特照明电子有限公司工作地点：其他发布时间：2009-6-6
- The radiated emissions from a symmetrical and an asymmetrical PCB layout were evaluated.Some results and layout regulations were presented. 文中对上述方法进行了分析，在此基础上通过一个对称电路和一个非对称电路的辐射场计算，提出了一些工程设计中减小辐射的设计准则。
- Job Description:Under the lead of senior engineer, FPGA and board level PCB layout designs. Qualifications:B.S. ...... ... 公司名称：梦奇芯片技术（上海）有限公司工作地点：上海市发布时间：2009-3-31
- The module design contains transmission line, bias and APC circuit of LD, low noise and high linearity RF circuit, FSK modern, monitor and control circuit design and PCB layout. 本文重点进行了光模块主要的电路包括传输线、LD偏置电路与APC电路、低噪声高线性射频电路、FSK调制与解调功能电路与监视控制功能电路的设计。
- PCB Layout and Library design. 线路板设计。
- Experience on embedded products, Familiar with tools of schematic design, PCB layout (with EMC) and RF. Knowledge on hardware circuitry, can analyze independently issues during development process. 有嵌入式产品的开发经验，熟练应用电子线路开发工具，有丰富的硬件电路知识，对开发过程中出现的问题能作独立分析。
- PCB Layout directive attached to the perimeter of a Blanket directive -- to which a Net Class directive is also attached -- will be applied to that net class, rather than each individual net. 一个PCB布局布线规则指示器与网络类指示器同时添加到覆盖区指示器的边框，将会把PCB规则适用到网络类，而不是单个的网络。
