您要查找的是不是：
- Oil pan drain plug gasket 油底壳放油塞垫片
- oil pan drain plug 放油塞
- REMOVE THE DRAIN PLUG AND DRAIN THE OIL. 旋开排油栓排掉机油。
- REMOVE THE OIL DRAIN PLUG, AND DRAIN THE OIL. 取出排油栓
- oil pan drain cock 油盘放油旋塞
- Tighten the oil, drain plug and, fill the oil to the, oil filler neck. 拧紧排油栓,注入机油至机油过滤器颈部。
- Fill the oil pan with oil to the specified level. 用油填充油底壳到规定油面。
- Loosen oil pan bolts and remove the front bolt at each side. 松动油底壳螺栓，拆下每一面的前螺栓。
- The bottom of the block is covered with an oil pan or oil sump. 缸体的顶部是气缸盖，它组成了燃烧室，缸体底部是油底壳。
- This picture was taken after the oil change had been completed.But I really wanted to show how we loosened the drain plug with the tool.See the double-headed wrench, one open and one closed. 这张照片是换好机油后所拍的;因为我实在很想告诉大家我是使用何种工具将洩油螺丝松开的;瞧这有双头的扳手;一头有开口;一头是圆的中间有孔的.
- Gasoline vapor also condenses on cold engine parts and drips down into oil pan. 汽油蒸气会凝结在冷的发动机零件上，然后流入油底壳。
- Check all drain plugs are fitted. 检查放泄塞是否已装好。
- Remove drain plug from bulkhead fitting and install valve assembly. Hand tighten. 从堵头连接件上拆卸排泄塞,并安装阀门总成。用手紧固。
- If the level is correct, fluid should just trickle, or drip out of, the centre of the drain plug. 如果油量正确，你只会见到波箱油慢慢滴或者流出黎。
- Trim or remove excess sealant film in the rear main cap oil pan gasket groovDO NOT remove the sealant inside the rear main cap slots. 修整或清除后主盖机油底壳垫圈凹槽中过多的密封剂薄膜。切勿清除在后主盖槽中的密封剂。
- The oil pump in the lubricating system draws oil from the oil pan and sends it to all working parts in the engine. 润滑系统中的机油泵从油底壳抽取油并把油输送到发动机内全部正在工作的部分。
- With it, the structure of the 6105 QA diesel oil pan for lower noise is optimized. 并用此系统进行了6105QA柴油机油底壳的低噪声结构的优化设计。
- And the other two rubber cushion seats 3 on the hinge side B are fixed by using a rubber-based adhesive. Then, oil pan 4 is placed. 再用螺钉2把铰链侧B的2个头部胶垫座3钉好固定，然后把底槽4放上去。
- Fill oil pan 1 with JUKI Machine Oil No. 7 up to HIGH mark A.When the oil level lowers below LOW mark B, refill the oil pan with the specified oil. 请把JUKI Machine Oil No.;1机油倒进油槽1里，一直加到HIGH标记A的位置。油槽的油面降到LOW标记B以下时，请再次补充机油。
- The oil pan and the lower part of the cylinder block together are called the crankcase; they enclose, or encase, the crankshaft. 油底壳和气缸体的下半部分一同被叫做曲轴箱；他们把曲轴封闭起来。
