您要查找的是不是:
- Normal tolerance limit 正态容差上限
- Stricter acceptable tolerance limit values for customers/sales. 加严的顾客/销售接受容差限值。
- The compaction force of the prepared punch exceeds the tolerance limit plus. 标记冲杆压力正偏差超过允许范围。
- The diagnosis principle and diagnosability conditions are proposed, and the normal tolerance network test nede voltage interval are given by interval iterative algorithm. 该方法给出了容差情况下诊断的原理和可诊断性条件,并利用区间迭代算法,给出了容差网络无故障情况下的测试节点电压范围。
- The compaction force of the prepared punch is lying outside the tolerance limit plus. 标记冲杆压力在正偏差之外。
- Ensure with each setting that the compaction force of the prepared punch exceeds the tolerance limit plus. 确保每个标记的压片冲杆的压力设定超过压力正偏差。
- Pay attention that the main pressure set value does not exceed the tolerance limit plus. 注意主压力设定值不能超过正公差。
- The Normal tolerances are in accordance with ISO 492:2002. 普通级公差符合2002年的ISO 492标准。
- Pay attention that the main pressure set value does not fall below the tolerance limit plus. 注意主压力设定值不能低于正公差范围。
- SKF thrust ball bearings are made to Normal tolerances as standard. SKF推力球轴承以普通级公差为标准。
- Objective To study the tolerance limit of crewman's arms to windblast with and without protective devices. 摘要目的研究人上肢有/无防护时耐受高速气流吹袭限值;
- Objective To study the tolerance limit of crewman s arms to windblast with and without protective devices. 目的研究人上肢有/无防护时耐受高速气流吹袭限值;为防护装置的设计要求提供试验依据。
- The tablet press is running in set up mode and the compaction force of the prepared punch is still lying outside the tolerance limit plus. 片剂按设定模式运行,标记冲杆压力在正公差之外。
- Cones and cups having a width tolerance that differs from the Normal tolerance are identified by a designation suffix according to table 2 where the actual tolerance values are provided. 宽度公差同普通级公差不同的内锥体和外锥环圈根据表2以型号后缀表示,实际公差数值见表。
- Start the tablet press and ensure that the compaction force of the prepared punch still exceeds the tolerance limit plus. 启动压片,确保标记冲杆压力在正公差之外。
- In the meantime, the tolerance limit of coordinate difference in the station for site testing is given and it is possible to test total station coordinate trave rse in site. 同时,根据该原理,给出了测站坐标差限值,从而实现了全站仪坐标导线的现场检核。
- The compaction forces of the other punches are within the tolerance limits. 其他冲杆压力在偏差范围内。
- Bearings up to and including 300 mm bore diameter are produced to higher precision than the ISO Normal tolerances. 孔径达(含)300mm的轴承的制造,使用比ISO正常公差更高的精确度。
- It wants to anchor inflationary expectations after the painful experience of the past year, when inflation stayed well above the tolerance limit of 5 percent. 经过了去年的痛苦经历,在通货膨胀的水准远高于容忍限度5%25的时候,它想让通货膨胀的预期抛锚。
- SKF four-point contact ball bearings are produced as standard to Normal tolerances. 标准生产的SKF四点接触球轴承符合普通级公差。