您要查找的是不是：
- There is no shape control in Visual Basic 2005. 在Visual Basic 2005中没有形状控件。
- Shape control was added at design time. 控件是在设计时添加的。
- In fact, SFR is heavily related to shape control. 自由规程轧制问题本质上是板形控制问题。
- The actual-3 dB main lobe width is a bit wider than in the ideal case that neglects the element size. 结果表明:阵元宽度对主瓣半功率点宽度的影响非常有限,而且不同的阵元宽度造成的半功率点宽度之间的差异也很小。
- At last,a simulation example of main lobe clutter power for low altitude and ... 最后给出了一低空远界理论弹道主瓣杂波功率的仿真样例。
- The main feature of AGC, tension measurement system, shape control, etc. of the Panzhihua Irou &Steel Co. 4 stands HC cold rolling mill are analyzed and descried in detail. 分析并阐述了攀钢4机架六辊HC机组AGC、张力测量、板形测量控制等系统的主要特点；
- For short biphase codes,the main lobe to sidelobe ratio of pulse compression is low,so sidelobe suppression is necessary. 二相码信号是一类常见的脉冲编码信号,但码较短时,匹配滤波的主副比不高,需要采用旁瓣抑制技术。
- Based on uniform line array,the sonar equation of active sonar beam main lobe and side lobe interfered by noise-jammer are presented. 研究了噪声干扰器对鱼雷主动声呐的对抗原理,以等间隔直线阵为例,分别给出了干扰器对鱼雷主动声呐主瓣和旁瓣的干扰方程。
- The Shape control in Visual Basic 6.0 Has no equivalent in Visual Basic 2005. Visual Basic 6.;0中的Shape控件在Visual Basic 2005中没有等效项。
- The directivity of forming beam are prominent, the width of main lobe is distinct, and producing wavy plan with more powerful, which make for scanning in space. 形成波束指向性突出，主瓣宽度明显，延时产生的波阵面能量较强，有利于空间扫描。
- Shape control is control profile and control flatness of strip or sheet. 板形控制是控制带材或是薄钢板横断面形状和纵向平直度的。
- The result reveals that small geometric focal length and large angle may decrease the -3dB focal area, and increase length to width ratio and the pressure magnitude of main lobe. 由结果得知，曲率半径愈小张角愈大会导致烧灼面积减小、长宽比增加以及压力主峰值的提高。
- This paper has introduced the roll system, the construction of mill, the main parameters, the shape control actuators and the tension control system of the new six high mill used in laboratory. 介绍新开发的实验室用新型六辊轧机的辊系配置、轧机结构、主要参数、板形调整机构及张力控制系统。
- This paper analyzes the main reasons of influencing plate shape in rolling process, and introduces the plate shape control equipment and rolling strategy in Angang steckel mill production line. 分析了影响轧制过程中轧件板形的主要因素 ,介绍了安钢炉卷轧机生产线上采用的板形控制设备和轧制策略。
- Virtually LPI guide radar is a radar which stacks up against with ESM receiver of target in system detection sensitivenes,therefore in the system design it should consider the technology measures emphaticaly to ensure its antenna main lobe LPI capability. LPI制导雷达实质上是一种从系统上与目标的ESM接收机进行探测灵敏度较量的雷达,因此在系统设计上应着重考虑使其天线主瓣LPI的技术措施。
- This method more effectively suppresses spatial nonstationary and stationary noise than the adaptive null-forming beamformer method by using a rotatable main lobe in the 2-D plane. 该方法克服了自适应零限波束形成只能抑制空间相干噪声的缺点,并得到可在二维平面上旋转的波束主瓣。
- In the Visual Basic 6.0 Example, the Shape control is used; it assumes that a Line control was added at design time. 在Visual Basic 6.;0示例中使用Shape控件;其中假定Line控件是在设计时添加的。
- In the other hand, after pulse compression processing, the output signal's main lobe will be extended and its amplitude or phase will be modulated, and the range resolution will descend too. 由于信号带宽的损失，脉压输出回波信号的主瓣展宽，距离分辨力下降；另外，主瓣幅度或相位还会受到调制。
- This paper introduces CVC technique briefly that improves the basic principle of shape control. 介绍了CVC技术改善板形的基本原理。
- Simulation results show that with 13 unit lasers, a beam with the flatness of less than 1% in the optimizing region can be achieved.The main lobe contains over 95% of the total power. 计算结果表明：13个单元光源所合成的远场光束可在优化区域内达到平坦度小于1%25，对应主峰包含95%25以上的总能量。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
