您要查找的是不是：
- Inner type joint union nut 内锥接头活套螺母
- The measuring insert is fixed to the case by a union nut. 插入测量头是通过联管螺母固定在外壳上。
- Single Entry Valves - slightly loosen single Union Nut. 单进入阀门-将单活接头螺母略微放松。
- Do not use Union Nut to draw together system components. 不要采用活接头螺母来将系统部件拉在一起。
- In order to prevent mishaps with the union nut, slide it (smallest bore first) over the pipe or nipple-and-flange hub (when flanging) before making the joint to the end connector. 为了防止管接头螺母的意外事故，在连接到端口连接件之前，(先从最小的阀腔开始)将它滑到管道或管嘴-法兰中枢上(当进行法兰连接时)。
- In order to prevent mishaps with the union nut, slide it (smallest bore first) over the pipe or nipple and flange hub (when flanging) before making the joint to the end connector. 为了防止与管接螺母相关的事故，在连接到端口连接件之前，先将其(最小的内径朝前)滑入管道或管嘴和法兰毂(当法兰连接时)上。
- Remove the Model 7 from the line (union nut and adapter remain in the line). 从管道上拆卸型号7(接头螺母和适配器留在管道上)。
- If the inheriting type (the outer type in the nesting) must inherit from the inner type, move the inner type out of the outer type. 如果继承类型(嵌套中的外部类型)必须从内部类型继承,请将内部类型移出外部类型。
- Reinstall the valve body and union nuts only after the joint has fully cured. 只有在连接完全成功粘固后，才能够重新安装阀门阀体。
- A inner type stop is utilized to limit the amplitude of the violent low frequency precession of the rotorbearing system which is the critical part of the experimental flywheel energy system. 利用限位器来限制储能飞轮实验转子的大幅度低频异步进动,设计了转子与限位器碰摩试验装置,研究转子的碰摩振动。
- The results show that when there is no welding arc, the accuracy of the seam reconstruction is very high. But when there has the disturbing of welding arc, the square joint and the U type joint cannot be reconstructed with high precision. 试验证明，无弧光干扰时，对于V型、半V型、对接I型、U型、搭接等接缝重建精度很高，有弧光干扰时，对对接I型、U型重建效果欠佳。
- Gravity ball check valves are converted to foot valves by replacing the union nut and end connector on the receiving end ? seat end ? of the body with an F.V. screen housing assembly. 重力球形止回阀可以变为底阀，只需在接受端口-阀体的阀座端口，用一个F.;V
- Loosen the valve union nuts and slide them back over the end connections. 松开阀门的管接头螺母，并将其滑回到端口连接件上。
- Remove the union nuts and end connectors from the valve cartridge first. 首先从阀芯上拆卸管接头螺母和端口连接件。
- Loosen the valve union nuts and slide them back over the end connectors. 松开阀门的管接螺母，将其滑回到端口连接件上。
- differential resistance type joint meter 差阻式测缝计
- Slide the union nuts over the end connectors and screw onto the valve cartridge threads, no more than handtight. 将管接螺母移到端口连接件上，并且将螺纹套在阀腔的螺纹上，感到手紧后就停止。
- The “L”“T” type joints of P208 pump oil warm-up pipeline were scoured by the vortexing,and the evorsion led to crack in weld.The leakage reason and countermeasure were discussed. 分析了炼油装置P208泵预热油浆管线L、T型接头的涡流冲蚀导致焊缝开裂泄漏的原因，提出了工艺结构改进措施。
- I was allowed once into his inner sanctum. 我有一次获准进入他的内室。
- Slide the union nuts over the end connectors and screw onto the valve cartridge threads, no more than hand-tight. 将管接头螺母滑入端口连接件上，并且螺纹对上阀腔的螺纹，手紧后就停止。
