您要查找的是不是：
- Gaussian curve equation 高斯(氏)方程:正态分布曲线Y与X的函数关系
- The height curve equation h=a 0d a1 was most accordant the pattern of height with DBH. 对树高曲线方程而言 ,h=a0 da1 最符合火炬松树高随直径变化的规律。
- The impact of covariates on diagnostic test assessment can be deducted adopting the methods of ROC curve equation. 利用ROC曲线方程,可以扣除协变量对诊断试验结果评价的影响,并能够计算出在不同协变量取值下的ROC曲线下面积,提供更为丰富和可靠的信息。
- According to real tested data,it builds up CVC cambering curve equation by polynomial regression. 根据实测数据,采用多项式回归方法,建立CVC辊形曲线方程,并探讨了该方程的重要实际意义。
- The connected curve equation after spreading connected joint of taper container are derived, the new blanking method with computer is put forward. 导出了圆锥形容器接管交线在展开接管表面后的曲线方程，提出了用计算机绘制其交线，即放样下料的新方法。
- With variation of shearing angles, the strength curve equation of thenardite and calcium thenardite salt rocks are deduced. 另外，由变角剪切试验结果分别获得了无水芒硝和钙质芒硝岩盐的强度曲线方程。
- Relative areas under the two Gaussian curves were 1.73:1 and 1.85: 1, respectively, for spontaneous and evoked sparks. 在二个高斯曲线下的相对面积为1.;73:1(自发钙闪烁)及1
- Based on the tooth profile curve equation of inner rotors in cycloidal pump, the formula for displacement calculation of the pump are derived. 根据摆线泵内转子的齿廓曲线方程,推导出了摆线泵的排量计算公式。
- Based on production decline curve equation, through mathematical derivation, a kind of logarithmic type production decline curve equation is obtained. 在产量衰减曲线方程的基础上，通过数学推导，得到了一种对数型产量衰减曲线方程。
- The section curve equation of main stirring shaft is obtained by deducting the screw profile curve formation process of the stirring kneader. 摘要用数学方法对搅拌捏合机搅拌轴螺杆外形曲线的形成过程进行了详细的推导，得出了主搅拌轴截面曲线形状公式。
- The connected curve equation after spreading connected joint of taper container are derived，the new blanking method with computer is put forward. 导出了圆锥形容器接管交线在展开接管表面后的曲线方程，提出了用计算机绘制其交线，即放样下料的新方法。
- Based on Arps decline curve equation this paper presents the autoregressive model for analyzing the production exponential decline curve, the analysis is convenient and reliable. 本文基于Arps递减曲线方程，提出了油气田产量指数递减曲线分析的自 回归模型。
- A mechanics model for constant supporting spring hangers is put forward.Then from the working principle of constant hanger, the curve equation of cams is induced. 摘要建立恒力弹簧支吊架的力学模型，并根据恒力弹簧支吊架的工作机理，推导其凸轮的曲线微分方程。
- One kind of beam type gas injection packing support plate used in the column is introduced. The curve equation of the developed pattern of the arciform plate is presented. 介绍了塔器内梁型气体喷射式填料支承及其拱形板展开图,并通过详细计算给出了该展开图的曲线方程。
- The S-N curve equation and the fatigue cumulative damage model of metallic material and structure considering the damage and coaxing effect were detailed herein. 摘要给出了材料和结构在累积损伤的同时还具有强化作用的S-N曲线方程，并建立了程序载荷谱下产生损伤的同时还具有强化作用的疲劳累计损伤模型。
- The main types and characteristics of tandem rolling are presented,and the equivalent roll crown and its curve equation of paired and non-paired tandem rolling are derived. 简介了轧辊交叉轧制的主要型式及其特点，导出了轧辊成对交叉（对称交叉）和非对称交叉轧制的等效辊型凸度与等效辊型曲线方程。
- According to real tested data,it builds up CVC cambering curve equation by polynomial regression.This paper discusses practical significance of the equation. 根据实测数据,采用多项式回归方法,建立CVC辊形曲线方程,并探讨了该方程的重要实际意义。
- The daidzein standard curve equation was Y=71519X-85913 with correlation coefficient R2 =0.9937. The standard deviation(SD) was lower than 7% when six samples were continuously analyzed. 本论文只确定了分析黄豆苷元的方法，确定黄豆苷元标准工作曲线方程为Y=71519X-85913，相关系数R~2=0.;9937。 连续进样6次，标准偏差(SD)小于7%25。
- In this paper a new method of fitting curve equation is proposed , it uses EXCEL electronic form software and"Plan to ask and solve" function to fit the curve equation directly according to the data that are not linear relationg. 本文提出了一种拟合曲线方程的新方法 ,即利用EXCEL电子表格软件及其“规划求解”功能对非线数据直接拟合曲线方程。
- By using the deductive curve equation in the paper,as the designed amount of gross water is definite,correspondingly the curve equation in the upstream complex-arc segment of practical curve-shaped dyke on its Ogee section could be gotten. 利用本文推导的曲线方程,设计总水头一定,即可得到相应的曲线型实用堰渥奇(Ogee)剖面上游复合圆弧段的曲线方程。
