您要查找的是不是:
- The cylinder head is heavily finned for strength. 汽缸头附有许多突片以增加强度。
- This is achieved by using cylinder head gasket. 这通过使用气缸盖衬垫实现。
- Place the engine cylinder head over the dowels. 将引擎汽缸头放在销上。
- Cylinder Head, Cylinder Liner, Connecting Rod, Piston, Piston Ring, Fan Clutch and Engine Valve etc. 主营气缸盖,气缸套,活塞,活塞环,离合器,引擎气门等。
- Remove control cables from cylinder head cover clip. 从汽缸头盖扣夹上移去控制拉索。
- Clean the exhaust manifold and cylinder head mating surfaces. 清洁排气歧管和汽缸头配合面。
- The main defect of type YC4112Q cylinder head is blowhole. 气孔为YC4112Q气缸盖的主要缺陷。
- We are importer of cylinder head, pls contact with us. 我们求购汽车汽缸盖,请与我们联系。
- A design of multifunctional valve for the ERD was put forward, using a specially designed valve to replace the four valves situated on the cylinder end.The unit was greatly simplified. 论文提出了一种阀控余压能量回收装置专用多功能阀门的设计方案,用特殊设计的阀门代替原有的水压缸端四个电磁阀,有效简化了系统。
- Showing a pushrod V8 with four valves per cylinder, the diagram also reveals a turbocharging unit and inboard exhaust and outboard intakes. 表现出的两个V8引擎的每缸四气门,该图还揭示了涡轮增压装置和船排气和舷外摄入量。
- Cylinder heads heater plugs relay defective. 汽缸盖预热塞继电器故障。
- A two-valve filter has been rebuilded to a four valve filter to execute full automation in the technical reform of the Nanmen Waterworks in Jiaxing, Zhejiang Province. 介绍了嘉兴市南门水厂双阀滤池技改工程。
- The most common cylinder head types are the hemi, wedge, and semi-hemi. 最常见的气缸盖类型是半球形,楔形和准半球形。
- Cylinder head cover: Is suitable uses in the elegant Maha ship machine. 气缸盖罩:适用于雅玛哈船用机.;。
- Position the cylinder heads onto head gaskets and cylinder block. 将汽缸盖安置到汽缸盖罩垫和汽缸体上。
- Based on the processing at vibration signals of diesel cylinder head and by means of the power spectrum analysis with Euclidean distance distinguishing function,the valve train faults are diagnosed. 提出对柴油机气缸盖表面的振动信号进行处理,利用功率谱分析和欧几里德距离判别函数诊断气阀机构故障,并开发出了由工业控制计算机、数据采集板和软件所组成的柴油机气阀机构故障诊断系统。
- The cylinder head carries the valves, valve springs and the rockers on the rocker shaft, this part of the valve gear being worked by the push-rods. 气缸盖携带阀门,气门弹簧和在摇臂杆上的摇臂,这部分的气门传动机构通过推杆工作。
- Block front fork of valve disassemble tool onto cylinder head sub bolt hole, pressing this tool downwards by a force application bar until the two pieces of lock are falling down, see chart 3b. 在拆卸气门锁片时,用气门拆卸工具的前叉卡在缸盖付螺栓上,然后用加力杆向下压动气门拆卸工具,直到两锁片脱出为止,如图3b。
- Four valve pulse tube refrigerator 四阀脉管制冷机
- Install the engine cylinder head, push rods, rocker arms, bridges, pivots and engine cylinder head cover. 安装引擎汽缸盖、推杆、摇臂、桥、枢轴和引擎汽缸盖罩。