您要查找的是不是:
- To improve the low voltage problem at Omei substation, proper location and capacities for the STATCOMs are determined based on power flow simulations for the system under various operating conditions. 在并联补偿的稳态研究之中,为了改善峨眉汇流排电压过低的情形,考虑各种可能发生的事故来找出适当的并联补偿器装设地点;并且探讨三种不同事故下,针对不同的装置容量做分析来找出最佳的补偿容量。
- Three-dimensional flow simulations of the flight element in an intermeshing co-rotating twin screw extruder are performed by solving the Navier Stokes equations with a finite element package, ANSYS. 利用ANSYS有限元分析软件对啮合同向双螺杆挤出机的螺纹元件流场进行了三维等温非牛顿模拟分析。
- Wave Flow Simulations Over Arctic Leads 北极铅盖屋顶上空的波动气流模拟
- Bion J R.Steady and unsteady distorted inlet flow simulation for engine ground tests[R].AIAA 84-1490. 彭成一;马家驹;尹军飞.;新型畸变流场模拟装置[J]
- Tannous, A. G., “Air flow simulation in a minienvironment,” Solid State Technology, pp.9-18, 1996. 魏嘉言,“计算流力程式在无尘室空气流场分析之应用”,硕士论文,国立清华大学,新竹,2000年。
- An application of wheel flow simulator in the evaluation of pour point depressant is described in this paper. 探讨了用转轮流动模拟器评价原油降凝剂的效果和模拟输油管道输送添加降凝剂含蜡原油的工业性试验的可行性。
- Lien, H.C., Yang, J.C., and Yeh, K.C., “Bend flow simulation using a depth averaged two-dimensional model”, Hydrosoft‘96, 1996. 蔡东霖,黄良雄,杨锦钏,”分层分区概念应用于地层下陷模拟”,第九届水利工程研讨会,民国87年7月。
- At a rush time of construction intensity,earthwork excavation and traffic flow simulation analysis are validated whether it isreasonable.Thirdly. 对施工强度高峰时段土石方的开挖强度及交通运输主干道行车密度进行分析是否能满足要求。
- The short-core and long-core flow simulation t ests with cores of Shengli Oilfield during sandstone matrix acidizing are compar ed in this paper. 使用胜利油田的岩心对比了砂岩基质酸化中短岩心和长岩心流动模拟试验,试验证实常规土酸对地层造成较严重的酸化二次伤害;
- In the core pin cylinder extruder, the flow simulate non - Newtonian fluid of the compound was built using the flow analysis network technique. 在销钉机简挤出机上,建立非牛顿流体的流动模型,计算出压力场、流动场和螺杆的特性曲线。
- Three-dimensional flow simulation of mixing blocks in a conical twin screw extruder is performed with a fi nite element package, ANSYS. 利用ANSYS有限元分析软件对带有混合块的新型锥形双螺杆的混合段流场进行了三维模拟分析。
- LI Hai?feng, MU Zhong?bo, WU Yu?lin. The three dimensional turbulent flow simulation in semi?open centrifugal impeller [J]. Pump Technology, 2001(1): 915. 李海峰;穆忠波;吴玉林.;半开式离心泵叶轮内部三维紊流的数值模拟[J]
- The screw die has great superiority in producing wide and thick polymer sheet, so it is significant to study the flow simulation and parameters optimization on the screw die. 但长期以来,国内橡塑生产行业一直没有很理想的宽幅厚板材生产设备,而螺杆分配机头在生产宽幅厚板材时有很大的优势,故对螺杆分配机头进行流场模拟与参数优化是一项非常有意义的工作。
- In this paper we report the analysis of underfill encapsulation between the solder ball, micro-chip and substrate by experiment and 3D mold flow simulation. 文中主要探讨了覆晶封装底胶充填时,锡球、芯片及基板间的流动状况。
- And then management of chemical process flow simulation software respectively carrying out entire process flow simulation on this five kinds decarbonization handicraft. 运用化工流程模拟软件分别对这五种脱碳工艺进行全流程模拟;
- Three-dimensional flow simulation of mixing zones in a new conical twin screw extruder with mixing blocks is performed with a finite element package, ANSYS. 利用ANSYS有限元分析软件对带有混合块的新型锥形双螺杆的混合段流场进行了三维模拟分析。
- A free flow of water came from the pipe. 水从管道里通畅地流了出来。
- In convection, hot currents flow upwards. 在对流中热气流向上运动。
- After several pumps, the water began to flow. 用泵抽了几下之后,水流出来了。
- Three-dimensional flow simulation of kneading blocks in an intermeshing co-rotating twin screw extruder is performed by solving the Navier Stokes equations with a finite element package, ANSYS. 利用ANSYS有限元分析软件对啮合同向双螺杆挤出机的捏合块流场部分进行了三维模拟分析。