您要查找的是不是：
- The interface of the diamond film and the active filler metal was observed by scanning electron microscope - energy dispersive spectroscopy and X-ray to dislcose the bonding medanism mechanism. 用扫描电镜、电子探针及X射线衍射区研究了金刚石膜与活性钎料界面,揭示了钎焊界面的形成机理。
- Regression Modeling and Experimental Analysis of the Multi-element Cu Base Medium Temperature Brazing Filler Metal Powder with Fine Grain 多元铜基中温微晶硬钎料的试验研究及回归模型
- nickel-based active filler metal 镍基活性钎料
- Aerospace series - Gold base alloy AU-B40001 - Filler metal for brazing - Wire. 航空航天系列.;金基合金AU-B40001
- Cu-based active filler metal Cu基活性钎料
- active filler metal 活性钎料
- Ag-Cu-Ti active filler metal Ag-Cu-Ti活性合金焊料
- Ag-Ti active filler metal Ag-Ti活性钎料
- In order to develop new generation monolayer brazing CBN (cubic boron nitride) grinding wheels, two types of active filler alloys (Ni Cr and Ag Cu Ti) were tested in vacuum furnace. 为研制我国新一代单层钎焊CBN(立方氮化硼 )磨料砂轮 ,尝试Ni-Cr和Ag -Cu-Ti两种活性钎料 ,在真空炉中钎焊。
- Cold lap is a condition where the weld filler metal does not properly fuse with the base metal or the previous weld pass material (interpass cold lap). 冷隔？（未熔合）由于熔敷金属没有很好的与母材熔合或没与前道焊缝熔合（层间未熔合）。
- The effect of heat treatment on electrical conductivity of Cu based multi-component alloy was studied by metallographic microscope, TEM, SEM/EDS, XRD and conductance instrument. 借助金相显微镜、TEM、SEM/EDS、XRD及电导仪研究了热处理对铜基多元合金导电性能的影响。
- BRAZING OF Si_3N_4 CERAMIC USING RAPIDLY SOLIDIFIED Al-BASED ACTIVE FILLER METALS 用急冷Al基活性钎料钎焊Si_3N_4陶瓷的研究
- Investigation of Brazing Mechamism of Ceramics Si_3N_4 with Activated Filler Metal 活性钎料钎接Si_3N_4陶瓷的机理研究
- The hardness of Cu base composite is much higher than that of pure capper.The improve of mechanical properties is due to the block of dislocation by dispersion of alumina. 且铜基复合材料硬度值比纯铜高出许多，显示氧化铝的均匀散布能有效阻碍差排的滑移，提升其机械性质。
- They are readily weldable, in most cases, with or without filler metal. 多数此种合金可焊（不论加或不加焊料金属）。
- The application status of low temperature Cu base NC306 type catalyst for synthetic methanol in allied production equipment using natural gas and water gas as feed gas was introduced. 介绍了低温铜基NC306型甲醇合成催化剂在天然气与水煤气联合生产甲醇装置上的应用情况,总结了使用过程中的注意事项;
- An experimental investigation into a Neural Network(NN) based active vibration control of Intelligent Mechanisms is presented. 进行了基于神经网络的智能化机构振动主动控制的实验研究;
- Based on a great deal of welding procedure qualification data, the mechanical properties prediction models of welding joints were established according to base-metal composition, filler metal compo. 本文针对实际生产过程中,焊接工艺评定要做大量的工艺评定试验,提出了利用人工神经网络和遗传算法来对焊接接头力学性能预测的方法来改进焊接工艺评定。
- It is concluded that the fine AP can act as active filler in the polymer matrix and enhance the matrix properties. 研究得知,细AP粒子在聚合物基体中起有效的填充剂作用,并增强机体的性能。
- Graph Cuts Based Active Contours(GCBAC) approach is a combination of the optimization tool of graph cuts and the iterative deformation idea of active contours. 基于图割的活动轮廓算法是一个结合图割优化工具和活动轮廓模型迭代变形思想的目标分割算法。
