您要查找的是不是:
- Branch pipe layout 支管布置
- Make the nest among the branch Pipe. 在我稠密的树枝间筑巢、鸣叫。
- The inside of the branch pipe needs welding and grinding. 支管内部需补焊打磨。
- Pipe charts and statistics were obtained by processing the results of pipe layout to support the field production. 通过对管路布局结果进行数据后处理,生成导管加工统计信息和各种报表,以支持现场生产。
- An introduction was made on dedusting cover structure, wind amount, pipe layout and wind speed in the pipe, control mode of fans of the dedusting system and the system size. 论述了除尘罩结构形式、风量大小、管路布置及管内风速大小、风机运行调节方式、系统规模等与降低除尘系统能耗之间的关系。
- In the daily life, post deliver, bus dispatch, the pipe layout and so on can be abstract as VRP.The logistic allocation is a complicated systems engineering. 在现实生产和生活中,邮政投递问题、公共汽车调度问题、电力调度问题、管道铺设问题、计算机网络拓扑设计问题等都可以抽象为物流配送车辆路径优化问题。
- When a pipe need to serve several equipments, or need to be led part flux, it is necessary to use branch pipe. 当一根钢管需要供应多台机组、或者需从钢管中引走一部分流量供其它用途时,便需要设置岔管。
- BRANCH PIPE VALVES. STOPCOCKS AND DRAW-OFF COCKS. GENERAL. NOMINAL PRESSURE PN 10. 支流阀.;关闭阀和给水阀
- Developed excogitates of two decumbence and one hovizoutal molding die, realized increasing height of branch pipe of heat pressure tee and reducing radius of synodical arc of tee. 研制出两套立式模具和一套卧式模具,实现了用工艺方法增加热挤压三通支管高度,缩小三通相贯区内拐角处圆弧半径的目的。
- In this paper, the improving method and programming arithmetic of pipe layout drawing for tabular heat exchanger were introduced, which has been used in the relevant module in PVCAD. 介绍了PVCAD软件包管壳式换热器模块布管图的计算机改进方法以及程序算法。
- The diameter (opening position, outer painting) of this branch pipe is not correct. It must be fabricated in accordance with the drawing. 这一支管通径(开的位置,外部涂装)不对,一定要按照图纸施工。
- Aiming at the importance of pipe system and the disadvantages of manual pipe layout in mechatronics, pipe layout design in Virtual Environment (VE) with flexible pipe model was put forward. 摘要针对机电产品中管路系统的重要性和手工布管的缺点,提出了一种基于柔性导管模型的虚拟环境下管路布局设计方法。
- The UHMWPE tee joint was made by a kind of specific designed equipment in which the branch pipe and main pipe cut from UHMWPE pipe were welt into integer. 以UHMWPE管材为原料,在特殊设计的设备上,将支管和直管沿交接线熔接在一起,可制得各种规格的UHMWPE三通。
- Experience in equipment layout, piping routine study, piping layout, isometrics, piping material take off and pipe support design. 拥有在总体布置、管道走向、管道布置图、ISO图、材料表和管道支撑的设计经验;
- A spray bank is composed of multiple main headers, branch pipes and individual connection pipes for each spray nozzle. 淋水管排由多个主管路,支管以及连接各个喷嘴的独立的连接管组成。
- For branch pipe with few welding seam (e.g. blowdown, instrument component etc) numbering can be conducted as a integrity with its connected pipes. 遇到焊缝数量较少的支管(如排污,放空,仪表元件等支管)可以把该部分与其相连接的管道作为一个整体,进行编号。
- Based on the FEM simulation results, a series of UPVC branch pipes were prepared successfully in a custom-built bulge forming test-bed. 在模拟和优化的基础上,利用自行设计的实验台成功地实现了UPVC三通管的挤胀成型。
- A lot of branch pipes mounted on the water distributor and each pipe has a spout at its outer end, which can refract water towards around thus to form a ball body. 是在一个球形配水体上辐射安装着许多支管,每根支管的外端装有向周围折射的喷嘴,从而组成一个球体。
- The formula to calculate the diameter of branch pipes and ellipse girth was given when the diameter of main pipe is known or reverse to resolve,discussed calculation accuracy. 给出了由已知主管相贯线处直径确定分支管直径和椭圆周长或反向求解的计算公式,讨论了精度。
- Misunderstanding in Design of Piping Layout 谈谈配管设计的误区