您要查找的是不是：
- Two kinds of boiler design methods are developed. 开发了锅炉设计的两种方法。
- Analyses the causes of smoke condensation and corrosion in gas-fired hot water boilers. Points out preventing measures in boiler design and operation. 分析了燃气热水锅炉烟气结露及腐蚀原因，从锅炉房设计与运行管理两方面提出了预防措施。
- Known marine or land boiler very well, 3 years experience in boiler sales; Person who has working experience in shipping institute, shipyard and boiler design would be preferred. 熟悉船用或陆用锅炉,3年以上锅炉销售经验,有在船舶设计所、船厂或锅炉设计工作经验优先考虑。
- B&W's unique IR-CFB boiler design employs a patented two-stage particle separation system to provide high-solids loading and a uniform furnace temperature profile. 独特的IR-CFB锅炉设计采用获得专利的两级颗粒分离系统从而具备高固体份装载和均衡的炉膛温度。
- The pressure of sweeping shall not exceed the design pressure of the container or the piping system. 吹扫压力不得超过容器和管道系统的设计压力。
- These include boiler design, cooling water conditions, burner type, design steam conditions and environmental controls that capture and remove pollutants. 包括锅炉结构、冷却水条件、火炉类型、设计蒸汽条件和截留去除污染物质的环境管理。
- So round shape of cracks (2C/a =2)was a stable shape when cracks developed on the design pressure. 因而在设计压力下发生裂纹传播时,接近圆形的裂纹形状(即2C/a=2)将是一个比较稳定的形状。
- The seal air fans deliver a design pressure that is above the operating pressure in the flue work. 密封风机能使空气达到设定的压力，此压力应高于烟气在烟道中的运行压力。
- A boiler designed for the pulverized coal or lignite to be consumed. 为燃烧粉状煤或褐煤设计的锅炉。
- All stream jackets are constructed from carbon steel materials and are welded to the valve body. Design pressure is 300 psi unless otherwise noted. 所有蒸汽套都采用碳钢材料制造,并焊接在阀体上。除非另有指定,否则设计压力均为300 psi。
- Reciprocating pumps and compressors require pressure relief valves when the stalling pressure exceeds cylinder design pressure. 当停转压力超过汽缸设计压力的时候，往复泵和压缩机要求安装安全阀。
- The design features, coal properties, main systems, as well as trial operation and combustion adjustment of a 1025t/h Wshaped flame boiler in Shaoguan PowerPlant have been presented, the problems existin gin boiler design and in operation being discussed. 介绍了韶关电厂 10 2 5t/hW型火焰锅炉的设计特性、燃煤特性、主要系统 ,以及锅炉试运行和燃烧调整情况 ,对锅炉设计和运行中存在的问题进行了分析。
- It is confirmed that the sinusoidal gear can be easily undercut with a specific addendum height value decided only by the design pressure angle of the gear. 经讨论和仿真证实;正弦齿条所生成的齿轮在一个特定的齿顶高下最容易发生根切;该齿顶高数值只取决于正弦齿轮的设计压力角.
- In 1983, KZL4-13 drill bar fire grate boiler designed and trail-manufactured by itself obtained national high quality product certificate. 1983年，自行设计试制的KZL4-13钻条炉排锅炉荣获省优质产品证书。
- Design Pressure barg , 7.0+F.V. 表示设计压力为：内压7.;0，外压全真空。
- Can argon arc root welding and manual arc cap welding be substituted with common manual arc welding on seamless steel line pipe below 5mm wall thickness with 9.5Mpa design pressure? 壁厚 5mm以下的无缝钢管用于设计压力9.;5MPa的管线，能否采用普通手工电弧焊工艺代替氩弧焊打底、手工电弧焊盖面工艺施焊?
- Experienced in different boiler design disciplines 不同锅炉设计经验
- The simulations show that 2L-MuRR improves the RRF capacity greatly,over 70%. By using 2L-MuRR,SMT can achieve the same high performance with fewer rename registers,effectively reducing the design pressure on the register file. 模拟实验表明;2L-MuRR显著提高了RRF的存储能力(70%25以上);能以较少的重命名寄存器满足SMT高并行度的要求;有效缓解了寄存器文件的设计压力.
- Accordingly,the least teeth number without undercutting is also decided only by the design pressure angle of the gear,without any relation to the coefficient of addendum height of the gear. 相应的无根切最少齿数也仅取决于正弦齿轮的设计压力角;而与齿顶高系数值无关.
- Discussions on EDF 600 MW CFB Boiler Design 法国电力公司600MW超临界CFB锅炉设计进展
