您要查找的是不是：
- The interface of the diamond film and the active filler metal was observed by scanning electron microscope - energy dispersive spectroscopy and X-ray to dislcose the bonding medanism mechanism. 用扫描电镜、电子探针及X射线衍射区研究了金刚石膜与活性钎料界面,揭示了钎焊界面的形成机理。
- nickel-based active filler metal 镍基活性钎料
- In order to develop new generation monolayer brazing CBN (cubic boron nitride) grinding wheels, two types of active filler alloys (Ni Cr and Ag Cu Ti) were tested in vacuum furnace. 为研制我国新一代单层钎焊CBN(立方氮化硼 )磨料砂轮 ,尝试Ni-Cr和Ag -Cu-Ti两种活性钎料 ,在真空炉中钎焊。
- Cu-based active filler metal Cu基活性钎料
- active filler metal 活性钎料
- Ag-Cu-Ti active filler metal Ag-Cu-Ti活性合金焊料
- Ag-Ti active filler metal Ag-Ti活性钎料
- Heating temperature,holding time and the composition of Ti in the active filler alloys effect the microstructure physical model of the joint between CVD diamond thick film and cemented carbide. 钎焊加热温度、保温时间、钎料层的含Ti量对CVD金刚石厚膜与硬质合金的接头结构模型有重要影响。
- Investigation of Brazing Mechamism of Ceramics Si_3N_4 with Activated Filler Metal 活性钎料钎接Si_3N_4陶瓷的机理研究
- BRAZING OF Si_3N_4 CERAMIC USING RAPIDLY SOLIDIFIED Al-BASED ACTIVE FILLER METALS 用急冷Al基活性钎料钎焊Si_3N_4陶瓷的研究
- Aerospace series - Gold base alloy AU-B40001 - Filler metal for brazing - Wire. 航空航天系列.;金基合金AU-B40001
- They are readily weldable, in most cases, with or without filler metal. 多数此种合金可焊（不论加或不加焊料金属）。
- However, for attaching nonpressure parts to pressure parts, the filler metal chemistry shall match the nominal chemistry of the pressure part. 但将非受压元件焊接受压元件时所用的填充金属，应与受压元件的标称化学组成相配。
- It is concluded that the fine AP can act as active filler in the polymer matrix and enhance the matrix properties. 研究得知,细AP粒子在聚合物基体中起有效的填充剂作用,并增强机体的性能。
- Influence of Sn and In in silver filler metal on spreadability and joint strength is studied. 研究了银基钎料中元素锡、铟对钎料铺展性能和接头的影响,分析了钎料的显微组织和锡、铟在钎料中的作用机理。
- The adjustment of the templating agents and diethyl tartrate (DET) ligand on the Ti active centers would cause the decreases in the catalytic activity and the increases in the selectivity. 而用含模板剂载体组装钛催化剂则显示出最高的环氧化选择性。胺基模板剂和DET配体对钛活性中心的调变作用将造成其活性下降,而环氧选择性上升。
- An appropriate (amount) of inert filler SiC (5%, mass fraction) or active filler nano-Al/Si powder is good for the joining of C_f/SiC composites. 适当加入惰性填料SiC(5%25,质量分数)或活性填料(纳米Al、Si粉)可以大幅度提高硅树脂对Cf/SiC复合材料的连接性能。
- Cold lap is a condition where the weld filler metal does not properly fuse with the base metal or the previous weld pass material (interpass cold lap). 冷隔？（未熔合）由于熔敷金属没有很好的与母材熔合或没与前道焊缝熔合（层间未熔合）。
- This paper concisely introduced the effects of the choice of curing agent,the flexibilizer quality and the active filler on the mechanical properties of the adhesive. 简要介绍了固化剂的选择、不同增韧剂的优劣及活性填料等材料对胶粘剂力学性能的影响。
